answersLogoWhite

0

The crank sensor is located behind the Harmonic balancer. Try not to break the rubber within the Harmonic balancer when removing or on the safe side replace both the Crank sensor and the Harmonic balancer ( the big pulley on the bottom - most part of the engine.)

User Avatar

Wiki User

15y ago

What else can I help you with?

Related Questions

How do you install a crank sensor to harmonic balancer on a eighty-eight delta royale 88 Oldsmobile?

To install the crank sensor on the harmonic balancer of an '88 Oldsmobile Delta 88, first ensure the engine is cool and disconnect the battery. Remove the harmonic balancer by loosening the bolt and using a puller if necessary. Position the new crank sensor in its designated mounting location, aligning it properly with the harmonic balancer’s signal wheel. Finally, secure the sensor, reconnect the battery, and test the installation for proper function.


1989 Oldsmobile delta 88 crankshaft sensor location?

The Crankshaft sensor is located behind the Harmonic Balancer on the front-passenger side


Your Oldsmobile delta stalls in warm weather?

you have a sensor problem.


Location of a cam sensor on a 1989 Oldsmobile delta 98 3800 v6?

The camshaft position sensor is located behind the water pump pulley. If looking directly at the pulley, it is at about the 10 O'clock position. TechJK ---------------------


Where is the low coolant sensor on a 1993 Oldsmobile Delta?

The low coolant sensor on a 1993 Oldsmobile Delta is typically located in the coolant reservoir tank. It is usually mounted near the bottom of the tank and may be accessed by removing the reservoir from the vehicle. If you're looking for it, check for a wire harness connected to the sensor that indicates the coolant level. Always consult the vehicle’s service manual for precise location details and instructions.


Where is the crank position sensor in a 1995 olds delta 88?

on a 1994 it's behind the harmonic balancer


Where is the map sensor on a 1989 Oldsmobile Delta 88?

At the end of your air cleaner tube is a square box with 4 screws and a plug in. This is your mapp sensor


Where the o2 sensor located on a 1986 Oldsmobile Delta '88?

On a 1986 Oldsmobile Delta '88, the oxygen (O2) sensor is typically located in the exhaust system, either in the exhaust manifold or just downstream of it, before the catalytic converter. To access it, you may need to raise the vehicle for better visibility. The sensor is usually threaded into the exhaust pipe and can be identified by its electrical connector.


Where is the engine coolant sensor located on a 1983 Oldsmobile delta 88?

On a 1983 Oldsmobile Delta 88, the engine coolant temperature sensor is typically located near the thermostat housing or on the engine block itself. It is usually found in the vicinity of the intake manifold, often on the driver's side. To access it, you may need to remove any obstructions, such as wiring or hoses. Always consult a repair manual for your specific model for precise location and removal instructions.


How do you change a cam shaft positioning sensor on a 1988 Oldsmobile Delta 88 3.8L?

See the Related Links for "Here" to the bottom for the answer.


How do you change a crank shaft sensor for a 93 Oldsmobile delta 88 royale?

on a 90 olds 88 royale your sensor sits inside the timing cover...will need to remove the harmonic balancer (need pulley for that) and remove two screws to take sensor out. replace all parts same way they came out and in same order. passenger side of engine in timing cover


Where is the o2 sensor located in a 1983 Oldsmobile delta 88?

In a 1983 Oldsmobile Delta 88, the oxygen sensor is typically located on the exhaust manifold or just downstream of it in the exhaust pipe. It may be found near the catalytic converter if the vehicle is equipped with one. If you're having trouble locating it, consulting the service manual for your specific model can provide additional guidance.