0
I'm not sure I understand the question. Some Kohler engine have oil filters and some do not. If it has a spin-on filter on the side of the engine then it does. If there is no spin-on filter then it does not have one any place else. I hope this is what you meant.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
Where is the oil filter on a 17 hp Briggs and stratton lawn mower engine?
Never seen one
Does a moto-master oil filter 17-1711-4 fit a 2000 Ford Ranger with a 3 liter engine?
Will a MOTO-MASTER filter with the number 17-1711-4 fit a 2000 Ford Ranger with 3 litre engine.
How many quarts of oil does a 02 ford 7.3 diesel engine hold?
17 quarts ============================================================================ *** That's too much oil *** According to the 2002 Ford F-250 , 7.3L DIESEL supplement : WITH engine oil filter change : ( 15.0 U.S. quarts )
Engine oil capacity in vauxhall astra 1.7 diesel gm?
Engine code 17 DT Grade 15W/40 semi synthetic Quantity including filter 4.5 Ltr
What fram oil filter fits 17 hp kawasocki?
Hi, The FRAM filter for your application is PH4967. The FRAM team
What does a motormaster oil filter number 17-1747-0 fit?
Nissan xtrail
What does a motomaster 17-1748-8 oil filter fit?
saturn s series
What size socket needed to change oil filter Saturn vue 2007?
Probably the same size -- 17 mm -- as for the 2006 Vue, if it's the 3.5 L V-6 engine.
What does 17-1749-6 oil filter fit?
A 1993-2000 Chevy truck or suburban. 5.7L engine and 2 wheel drive. 4 wheel drive use a different one.
How do change the oil filter in a 2004 range rover?
Range Rover 2003-2005 Models (BMW engine):Installation Notes:You will need a rare 36mm socket to loosen and remove your oil filter housing (see part # W136).Raise vehicle to access the under side of the engine. Support vehicle safely - vehicle ramps or lift recommended.Find the drain plug on the engine. It is located on the right side of the sump, close to two oil cooler lines.Position a suitable oil drain container under the sump.Using a 17mm box wrench, remove the drain plug, allowing oil to drain. Discard the copper seal washer (a new washer is included in our Oil Filter Kit # LPW000010)Lower the vehicle. Locate the oil filter housing in the left front of the engine compartment. It is near the left side of the radiator.Using a 36mm socket (our part # W136), remove the oil filter cap. Discard the 'O' ring.Remove and discard filter element.Fit new filter element large hole to the bottomInstall new 'O'-ring on cap and lube with some clean oil. Install cap and tighten to 18 foot-pounds torque.Raise vehicle and refit the drain plug with a new sealing ring. Tighten to 17 foot-pounds torque.Lower vehicle and fill with 9 quarts of 5W-30 oil. Run engine until oil lamp is turns off. Stop engine check oil level.
What tool do you need to change oil in Honda Rubicon?
a size 12 mm for the drain plug. and a size 17 for the oil filter housing.
How do you change the oil filter on a BMW r1150r motorcycle?
Engine Oil and Filter Change Tools Parts oil filter tool oil - 4 qts. hex bit socket - 8mm oil filter ratchet crush washer - drain plug torque wrench rubber gloves funnel oil drain pan rag 1. Remove the sump plates (skid/bash plates) - see page 18 for instructions. 2. Be sure the engine is hot (go for a short ride). 3. Place the oil drain pan under drain plug (bottom right side of engine). 4. Wear rubber gloves - oil is carcinogenic, plus when you accidentally touch the hot headers!!! or get hot oil!!! on your hands it won't hurt as much. 5. Remove the oil drain plug located to the right of the oil filter, 8mm hex bit socket. 6. Remove the oil filter, oil filter tool and ratchet. 7. Remove the oil filler cap to help draining. 8. Let drain for ~10 min. 9. Use the rag to remove any dirt from around the drain plug area and from the oil filter well. 10. Install the drain plug with a new crush washer and torque to 23 ft.lb. (32 Nm). 11. Fill the new oil filter with fresh oil. 12. Apply a thin coat of oil to the new oil filter rubber gasket. 13. Install the new oil filter and give it ¾ - 1 turn after first contact. 14. Add 3.75 - 3.9 qts. of oil total (NOT 4 qts.!!!) using a funnel or oil spout. 15. Install the oil filler cap. 16. Run engine at idle for 2 - 3 min. 17. Wait ~10 min. and check to be sure the oil level is at the dot in the center of the sight glass. 18. Check for any oil leaks at filter and drain plug. Note: You may get more consistent oil level readings if you put the bike on the sidestand for a few minutes and then put it on the centerstand.
