0
Do you have to remove power steering pump to remove head on a 1989 4.3 S-10?
Wiki User
∙ 17y ago
yes. Some GM pumps will require you to get a Power Steering pump pulley remover in order to get to the bolts to remove the pump from the aluminum bracket, so you can get to the bolt that goes to the head.
Wiki User
∙ 17y ago
Add your answer:
Earn +20 pts
Do you need a special tool to remove the power steering reservoir cap?
There is no special tool needed to remove the power steering reservoir cap of a Volkswagen Golf. It can be removed with a flat head screwdriver.
How do you remove power steering hose?
I need to know how to replace the hoses on my power steering system. I also need to know what type of hydraulic fluid and steering fluid it takes?? If my head gasket is bad and I put stop leak then why is it still overheating?? Where is the water going!!!
How do you replace power steering pump 1998 plmouth grand voyager 3.3 l?
The pulley has holes in it so you can stick a socket through on top of the bolt head. Sometimes the socket doesnt fit squaely on bolt head so you may just have to take power steering pulley off first to get to the two bolts that run throught the top and bottom of pump. This way might be the easiest. And of course you have to unloosen the lines that runs to it and it will come off. So they are only two bolts to take off, and you have to use a socket and a wrench, or two wrenches to remove bolt and nut.
How do you remove the power steering pully on 1999 350 suburban with 4wd Is the Allen head bolt a right or left hand thread?
The Allen head is NOT a bolt. Go to an Auto parts store and get a Power Steering Pulley Remover tool. The pulley is pressed on, there will be instructions with the tool or ask the counter person.
How do you replace power steering pump Mazda 3?
first remove the front bar cover from driver side second remove the driver side head light,third undo the plastic cover under the driver side guard,fourth remove the windscreen washer bottle.now u can see the electric power steering pump just undo it.
Where is the power steering fluid reservoir on a 86 Toyota minivan?
The power steering pump is located behind the passenger seat about 20inches from the emergency brake lever. Remove the carpet piece, there will be a small panel (top of the hump). Use a flat head screw driver or a 3/8 socket to remove the one bolt.
Can you have power steering fluid loss into the cylinder head from the power steering pump on a 2001 grand am with a 2.4L engine?
No But often power steering systems end up with red Automatic Trans Fluid in them and The auto trans Cooler in the readiator can leak into the cooling system and thus the Cylinder Head.
How do you remove stock head unit from 1989 Honda civic?
it pulls out.
How do you disarm the airbag on a 94 camaro and remove the steering wheel?
simply pull tha airbag fuse. remove the 4 torx head scres behind the airbag and remove airbag. unplug theelectrical connector. remove the big nut holding the steering whell. use a puller to remove the steering wheel.
How do you remove power steering pulley 1995 suburban How do you lock the pulley in place to remove Allen bolt?
It requires a special puller to remove the pulley. There is NO bolt are Allen head that has to be removed. The pulley is pressed on. You will also have to get a special tool to put the pulley back on too.
How do you remove the steering lock on a 1994 Ford Probe?
# Disable airbag system. # Remove steering column covers and lower instrument panel cover # Lower steering column # Disconnect the shift interlock cable from ignition lock housing # The lock assembly is clamped to the steering column by two shear-head bolts. Drill heads off each bolt and remove the bracket. # Remove the steering lock assembly from the steering column
How do you replace the water pump on a 1989 Mercedes-Benz 300sel?
Drain coolant, Remove air cleaner assembly. disconnect water hoses from radiator. remove drive belt and power steering pump. remove water pump drive pulley. Loosen hose clamps on cylinder head-to-water pump cooling line. remove mountin bolts and water pump. reverse to install. I highly recomend taking this one to a shop but if you feel lucky, this is how to do it.
