Yes, the 1989 Ranger does have a PCV valve. I can speak for the 2.3 liter 4-cylinder version only. If you stand on the driver side of the engine compartment you will see the intake manifold (silver cast looking with the name Ford on it), on the bottom of the intake there is a 90 degree elbow (the intake forms a "Y" and if you look through the "Y" you can see the elbow) that points back toward the firewall. Connected to this is a rubber hose that routes back toward the firewall and then turns down at the firewall-side of the intake. If you follow this hose along you will come to the PCV valve. The valve is installed in the hose and connects to another rubber hose on the other side of the PCV valve. Hope this helps.
The 1995 Ford Ranger 3.0 liter engine PCV valve can be found on the top of the engine. The PCV valve will be on the back side of the air cleaner.
The PCV valve, on your Ford Ranger 2.5 liter engine, is located on the outside of the air cleaner housing. The valve is on the back of the housing.
On 2002 Ranger 3.0L, the PCV valve is mounted in the valve cover near the brake booster.
Hey Vince==It is in the valve cover. GoodluckJoe
On a 2000 Ford Ranger , 4.0 liter EFI , V6 engine : The PCV valve is on the drivers side engine valve cover , on the top of the valve cover , near the REAR of the cover
On 3.0L and 4.0L engines, the PCV valve is mounted in the valve cover near the brake booster. - Haynes Repair Manual #36071 - 1993-2005 Ford Ranger Pickups.
I believe it is on the valve cover , drivers side of engine , towards the rear
On a 2000 Ford Ranger , 4.0 liter EFI , V6 engine : The PCV valve is on top of the drivers side engine valve cover It is near the rear of the valve cover ( towards the firewall end )
There is no PCV valve on the 2.2 Liter engine.
In the top of the valve cover , on the drivers side of the engine , near the rear of the valve cover , next to the firewall
It is located behind (toward the rear of truck) The oil add chamber on the passanger side valve cover. Pull the hose out of the valve cover and there you'll find the PCV Valve
On a 1996 Ford Ranger , 4.0 : The PCV valve is on top of the drivers side engine valve cover , near the rear of the valve cover
where is the pcv valve on a 1992 f150 with 5.0 liter
on the engine valve cover , drivers side , towards rear of cover , near firewall
That is the Positive Crankcase Ventilation ( PCV ) valve Depending on the model year and engine size there are different part numbers for the PCV valve
The pcv valve is located on the top of the valve cover. It is a plug in type and just pulls out.
The PCV valve on a 2002 Chevy Suburban 6.0 liter engine is located in the engine. You cannot miss the valve.
The PCV valve on a 1992 Ranger 3.0 V6 is on the drivers side and fits into the manifold cover near the firewall. There are 2 hoses which conect to the top of the PCV Valve.
The pcv valve is located behind the clip that holds the by-pass radiator hose below the intake manifold. This valve is in one of the poorest places they could have put it, very difficult to get to to change a $4.16 part. Once you find your pcv valve, good luck getting it out!
On a 1997 Ford Ranger , 4.0 EFI engine : The PCV valve is on the top of the drivers side engine valve cover , near the rear
its in the valve cover by the brake booster
The PCV valve on the 98 is located in the top of the right (driver's side) valve cover near the back.
I know on the 4.0 liter V6 it is on the drivers side valve cover near the rear of the valve cover ( near the firewall )
No, it does not.
I would say that my 1998 S-10 does not have a PCV valve, at all, anywhere.