answersLogoWhite

0

Drum on which cable is wound?

User Avatar

Anonymous

13y ago
Updated: 8/20/2019

Capstan

User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

What pulley does a tow truck use?

A tow truck typically uses a type of pulley system known as a winch. The winch consists of a spool or drum, around which a cable or rope is wound. When the winch is engaged, it pulls the cable, allowing the tow truck to lift and secure a vehicle for transport. This system often incorporates a series of sheaves or pulleys to redirect the cable and increase lifting efficiency.


What is a telegraph cable?

Simply a cable through which telegraph signals were sent. It was heavy, copper and wound with lots of insulation of rubber and pitch.


How do you adjust cables in brake drum?

You don't normally adjust in the brake drum. There is usually an adjuster about halfway to the back, under the driver side. This is an oblong metal frame where the front cable joins the cable to the rear splitter. You tighten a nut in this box to adjust length of cable.


Where does cable on on rear drum brakes hook to?

You are possibly referring to the emergency or parking brake cable. This hooks to a pedal or lever in the drivers area.


What an emergency brake looks like?

Depends on the vehicle; could be drum/shoe arrangement with cable actuation; could be rear disc brake pads with cable or could be rear disc brake with inner shoe and drum inside the rotor.


How do you attach garage door cables properly?

To attach garage door cables properly, first, secure the cable drum to the torsion tube. Then, thread the cable through the drum and attach it to the bottom fixture of the garage door. Make sure the cable is properly tensioned and aligned to prevent any issues with the door's operation.


How to tighten Daewoo matiz handbrake cable?

I have removed my drake drum today and wondered how to adjust the hand brake as it seams not to work as good as before .i removed drum to change wheel bearing


How can I connect electronic drums to a computer?

You can connect electronic drums to a computer using a USB cable or a MIDI interface. Simply plug the cable into the drum module and the computer's USB port or MIDI interface. Then, configure the drum software on your computer to recognize the electronic drums as a MIDI input device.


How do you fix a stuck rear passenger parking brake on a 2000 Plymouth voyager?

Sadly, I'm answering my own question. What I did was cut the cable 6" from the brake drum. Important note: the parking brake cable NOT the brake line. After I cut the cable I removed the 6" section of cable and the spring from inside the drum, then sprayed a liberal amount of PB Blaster which allowed the brake to release. Now my P.O.S. drives again. For now....


What to spray on a seized emergency brake cable?

Spraying it on the cable probably won't help. Take off the rear wheels and something like spray WD40 on the handbrake cable linkages. You could also give the drum a few smacks with a hammer - the vibration can free up a stuck linkage/cable. Might be a good idea to place a small block of wood against the drum and hit that with the hammer to avoid denting things.


How hard is it to change the right hand emergency brake cable in a 1982 2WD King Cab?

Not hard at all. Jack the car up and put a jack stand under it so you can safely slid under it. Remove the right tire and then remove the brake drum. You may need to do a little work to get this off depending on its condition. Then once inside the brake area you can locate the cable connector. It is a simple slip on type of connector and you don't need to remove all the parts to get to it. A long needle nose is helpful tho. Slide under the car and find the cable and follow it to the connector from the emergency brake handle. Remove the nuts that secure the cable in place. Then go back to the right brake drum remove the cable. It is pressed into place and might require a little pounding to get out. Look at the new one and you will get an idea of how it is held in place. Once out clean up that area for the new cable and install from the drum to the connector. Then reinstall the drum and adjust both the drum brakes and the cable. This typically took me about an hour and a half to complete with all the adjustments.


What type of e-brake does a 1997 park avenue have in it the drum brake type or the caliper pistion gets squesed by the cable?

97 park ave has four wheel disc brakes, not drum brakes