0
Find a jacuzzi filter valve handle for a model 225L sand filter?
Wiki User
∙ 14y ago
http://www.poolsinc.com/jacuzzi-bros-laser-160l-190l-225l-250l-parts.html
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How do you fix a jacuzzi filter that has a small amount of water coming out of the waste port when the ball valve is set to filter most water is exiting the return port?
You may need a new valve especially if you have tried or have succeeded in moving the valve position while the pump was running.
Where is the idle speed control valve on a Ford Fiesta 96 model?
its behind the air filter
What should you do if your pool filtered up fine but will not backwash?
You may have a large chunk blocking the discharge valve, try opening the valve with the pump off and moving a broom handle upinside the valve, you should have a two and one half inch valve for the dischargeso a handle or something smaller, just may be blocking the hole at the valve to let the water out.most people have a problem getting the filter to prime and keep running. If you have a popular punp and filter just remove the discharge valve and see if anything is blocking the hole.
How do you clean pool filters?
back-washing a sand filter sand filter with amultiport valve # Turn of the pump# while pressing down on valve handle, turn it from the FILTER to the BACKWASH position # start the pump # usually there is a clear bubble on or near the multiport valve. it shows the condition of the water. at first the water in it will look dirty when it clears up, turn of the pump.# Turn multiport valve handle to RINSE and Run it rinse for about 30 seconds seconds. # Turn off the pump then move the multiport valve handle to FILTER position # Turn pump back on and note lower pressure. ----Back washing a D.E. filter with a multiport valve; # Turn of the pump# while pressing down on valve handle, turn it from the FILTER to the BACKWASH position # Start the pump# Let the water run for 2 - 3 minutes or until it runs clear. Turn of the pump.# Turn multiport valve handle to RINSE and Run it rinse for about 5 to10 seconds. Turn of the pump.# Move the handle to BACKWASH. Turn on pump again until water runs clear. do this about 3 - 4 times, going from backwash to rinse, Backwash & Rinse, to ensure a thorough backwash. # Turn of the motor and move multiport valve handle back to the FILTER position # Turn pump back on# Add 1 lb D.E. powder per 10 sq ft of filter area. Check on the filter tank. ---- Cleaning a Cartridge filter # Turn of the pump # Open the air bleeder opened, # Remove the cover, # Remove the cartridge # Hose it thoroughly from top to bottom, until all of the debris stuck to it is gone # Soaking the cartridge in a TSP (trisodium-phosphate) or similar solution can be helpful especially with older filters that can suffer from blocked pores. NOTE Do not use TSP with Baquacil or Soft Swim for sanitation.----
Do you plug in a hose somewhere before setting to back wash an in ground pool?
Notnormally You may have to top up the water a bit because the back wash process tends to lower the water level of the pool a bit bit no hoses need to be plugged in anywhere as the backwash system is part of the filtration set up. Below I have put in backwash instructions---- back-washing a sand filter sand filter with amultiport valve # Turn of the pump# while pressing down on valve handle, turn it from the FILTER to the BACKWASH position # start the pump # usually there is a clear bubble on or near the multiport valve. it shows the condition of the water. at first the water in it will look dirty when it clears up, turn of the pump.# Turn multiport valve handle to RINSE and Run it rinse for about 30 seconds seconds. # Turn off the pump then move the multiport valve handle to FILTER position # Turn pump back on and note lower pressure. ----Back washing a D.E. filter with a multiport valve; # Turn of the pump# while pressing down on valve handle, turn it from the FILTER to the BACKWASH position # Start the pump# Let the water run for 2 - 3 minutes or until it runs clear. Turn of the pump.# Turn multiport valve handle to RINSE and Run it rinse for about 5 to10 seconds. Turn of the pump.# Move the handle to BACKWASH. Turn on pump again until water runs clear. do this about 3 - 4 times, going from backwash to rinse, Backwash & Rinse, to ensure a thorough backwash. # Turn of the motor and move multiport valve handle back to the FILTER position # Turn pump back on# Add 1 lb D.E. powder per 10 sq ft of filter area. Check on the filter tank. ----
Which way to turn handle on ball valve to open the valve?
The handle faces the direction of flow
Why does a jacuzzi drain?
If your Spa is attached to your pool more than likely your valve actuator is not set in the correct mode.
What Position of pool pump handle indicates what mode pump is in?
The pump ( the equipment with the motor attached) does not have a handle to turn or otherwise. But the filter ( the large tank) does have some sort of handle. Read that label at the handle. If this is a rotory valve the "handle" should always be turned clockwise for rotation and NEVER rotate the valve while the pump is on and running. Labels for the different positions should be positioned so as to see them from the top of the valve just under or around the valve top. Different valves will vary as to what positions you have available. They should be FILTER, BACK WASH, WASTE, BYPASS , ETC. These should be self explainetory. The "mode" of the pump is immaterial because the pump is either on or off. You need to get a glossary as to what the different components are before you tamper with anything. k
Fuel filter on a yz250f?
it is part of the fuel valve. there is a filter element on the inlet of the fuel valve in the tank.
Is the water line open or closed when the ball valve handle is in line with the pipe?
When the handle is in line with the pipe, the valve is open.
How can you lock water valve with round handle to prevent turning?
Handle locking device made by Walworth Valve company
What is causing water to leak from the base of an American standard cadet tub filler model 3985 attached to tile which surrounds your jacuzzi espree tub?
Is the leak occurring when filling the tub or all of the time? If during then your source is in the pipe from the valve handles to the spout. If at the valve then I would give some attention to the stem packing.
