answersLogoWhite

Top Answer
User Avatar
Wiki User
Answered 2006-08-26 02:07:47

I have not beat the tire problem but I have found alot of unhappy owners who have replaced the front end like me and still have the problem. I replaced ball joints, hubs, shocks you name it same thing.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Your Answer

Related Questions



www . motorcraft service . com ( no spaces ) Click on Owner Guides


It's on the left side of the dash. You have to open the driver's side door to access it.


I get better answers from my eight ball than a Ford website.


I just replaced the plugs in this truck and you need to pull both wheels. You then remove the weather flaps and can get to the plugs from there with regular socket tools nothing special. Don`t need to pull both wheels,just passenger with a wobble extension


It's between your engine air filter housing and the big rubber engine air intake tube


Behind the dash...you have to remove your glove compartment door, be careful not to set off the passenger air bag.


When you have your headlights on low beam pull the headlight switch on your dash towards you and push it back in to turn the fog lights on or off


inside front rotors,you well see wiring going to sensors,the rear sensor only one at the diff.right above drive shaft.


Engine temp getting too high, or poor quality gas. Try some f/i cleaner and some octane boost.


if you are near any black cat ask her to open-up her extended long leg and there in the middle of it you should see the sensor...hahaha


Assuming that your other doors lock and open properly check the solinoid for the drivers door.


Check out www . motorcraft service . com ( no spaces ) Click on Owner Guides The owners manual ( which includes the fuse box diagram ) can be viewed on-line


On a 2001 Ford Explorer Sport Trac , 4.0 litre SOHC , V6 engine : With engine oil filter change : ( 4.7 litres / 5.0 U.S. quarts of 5W-30 engine oil )


You can view the 2002 Ford Explorer Sport Trac owners manual on-line at : www . motorcraft service . com ( no spaces ) Click on Owner Guides ( the fuses and relays section starts on page 127 , it has the diagrams and lists )


Here is a link where you can get the manual in pdf format. https://web.msslib.dealerconnection.com/RightSite/getcontent/myfile.pdf?DMW_OBJECTID=09000c588024b0b6 Good luck Stop By Your Ford Dealership Parts Department. They Can Probable Run You A Copy Of The Fuse Placement. It Should Be In The Owners Manual Also. Try To Get Them To Order You A New One.


You need to get the original code for the pad and get your manuel. Or get a copy from Ford Online(free) that shows the steps to program. If you do not have the factory code it is in the back panel behind the back seat on the computer square box with the wiring harness attached to it. Above the tire jack. You might need to pull back the plastic to see it with a flash light. It is a 7 number code that is in large print.


This part must be obtained from the dealer. A little pricey but if it is leaking you will notice it is worth the money to get it fixed. The PCV assembly is a little more than the little piece you would see at Autozone. It consists of the PCV valve itself and then a long molded plastic piece that comes behind the engine. When looking at the engine the valve itself is on the left side of the block right on the top towards the front. However the tubing goes all the way back and behing the cover and ties in just behind the right side of the engine. It takes a little finesse to get the clip off but patience will have this changed in no time. Good luck... don't forget to put on the plastic gloves first! Davisbound


you will need a set of guages to do this, you will need to have the vehicle on max a/c with the windows closed. some visual indicators are oil around the joints on the air conditioning compressor mounted on the engine, or around the hoses and their seals. available from auto stores, and places such as target, walmart etc... are cans with pre-mounted gauges that give recommended operating range, typically 30-45 psi on the low side (the lager hose that is cold to the touch) DO NOT CONNECT TO THE HIGH SIDE CONNECTIONS TO INJECT COOLANT OR OIL! the high side (small hose) should be warm or significantly hot to the touch, and the low side (larger hose) should be cool to the touch. while the low side and expansion chamber shoudl be cold they shoudl not be building ice, if so your pressures are incorrect. if you have a manifold gauge set you can monitor the pressures on both sides of the compressor, and with recomendations from your local a/c parts distributor they can advise you on propper operating pressures for your specific vehicle.



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.