0
How can you drill a new hole in a wall right next to existing one?
Wiki User
∙ 12y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Should you drill a hole in your car muffler so the water will drain from it?
No, Do not drill a hole in your muffler! The water evaporate when the car gets warmed up. If you drill a hole in your muffler, The next time it gets inspected it will fail.
What quadrant is the greater omentum located in?
right next to the hole in your buttocks
Where is a firewall hole located on 2001 Honda Civic?
there is a little hole right under the hood next to the driver side door
What options do I have if one of the screws on the engine block is stripped on a 1993 acura integra 1.7L dohc b17a1 engine block?
There are a couple of options. If possible, you could drill the screw hole out to the next bigger size and tap it out to the next bigger size screw. Before you do this make sure you are not going to drill into a water jacket, oil port, or something else equally important. The next option is to have new threads heli-arced into the old hole. A quality machine shop will be able to do this for you.
Can you finish doodle jump?
No but I have gotten right next to the end spot, just died by monsters or a black hole.
How you can you drill faster with an electric hand drill?
You put a drill bit in the drill chuck, tighten with a chuck key, plug in to an outlet and pull the trigger to start the drill motor and apply medium pressure to what ever your making a hole in.
How do you Install sim card into iphone?
On the top of the phone next to the ear phone jack, there is a small hole. Find something small enough that will fit in the hole and push down on it. That releases the pop-up simcard holder located right next to it. Pull it out install away. On the top of the phone next to the ear phone jack, there is a small hole. Find something small enough that will fit in the hole and push down on it. That releases the pop-up simcard holder located right next to it. Pull it out install away.
Pontiac Aztec How do you release the lock on security key lock in the ignition?
There is a hole under the column right next to the ignition. put a pen in the hole and the key will now roll back to get it out of the ignition.
What is the spark plug wiring diagram for a 94 honda accord?
start from far right spark plug hole to the far right bottom distributor then the next one to that spark plug cylinder to the left of the distributor you just did then the next cylinder across the the closes one last one right next to it should be the location
How do you get behind the fence in national park in Pokemon crystal?
in the north side of the park there is a guy who plays gameboy. right next to him there is a hole in the fence. you can go through that hole and behind the fence. GOOD LUCK!!!
How do you add extra sockets in the bedroom?
If there is a crawl space under the house the best way is to run the wires under the home in the crawl space. Determine where you want to mount the outlets and find the wall studs. Either cut right next to the wall stud so you can mount a regular outlet box to the side of the stud with drywall screws, or cut between the studs and use a pop-in type outlet box. Measure up from the floor the same distance as the other outlet boxes with the cover removed and cut the hole for the new outlet box the very same height off the floor. Now removed the floor moulding and drill a very small hole right next to the wall directly below and center of the outlet box hole you just cut. Remove the outlet from the box of the one nearest to where you are installing the new one. Drill a hole in the bottom of the box big enough to run the new wire. Repeat the steps to drill a hole next to the wall. Place some sort of piece of wire in each of the holes you have drilled so the person who goes under the floor can see the object. That person will drill a 3/4" hole exactly 2" from the hole toward the wall you are working on. They can then feed a wire up through the hole into the outlet box or you can feed the wire down, whichever is the easiest. Run the wire from outlet to outlet and tie is all together. Repeat this for other outlet boxes. It may be necessary to remove the old outlet box completely and install a new one in order to ever get the new wire in place. Fill the holes you drilled in the floor with wood filler and replace the moulding. If you are working on an interior wall with no insulation it may be just as easy to do all this from the attic.
What is the best drill bit for hardened steel?
Coated carbide is the best. Uncoated is next.
