I've had to do several small patch jobs (8" x 8") due to rebar ties rusting through. I called several pool builders for 1.) advice on how to do the repair and 2.) materials. One local builder had some extra and filled a baggie for me. Getting ready for my fourth repair this morning. -Rick
Answer: I admit I'm not familiar with marcite. However, in regards to the rebar rust spots. Simply filling them in will allow them to return within a few months. Ideally, you'll need to cut down an inch or so, and use a grinder to grind down the long rebar/rebar tie. Then use a plaster patch. All other products to "cover" rebar rust spots are only temporary, and failure to eliminate the source of the rust will allow it to return soon.
It's Very easy. First use a grinder with a cut off wheel. Make a square using a strait edge with a black marker. Grind down about 1/2 to 3/4 inch. Remove marcite with a hammer and chisel down to the concrete. Clean area with a wire brush and wash with water and allow to dry. Marcite patch comes in 80lb pre-mixed bags. Call pool companies around your area. They can order it for you. You will also need a bonding agent such as weld crete. That only comes in 1 gallon cans. you can get this at hardware stores. Paint on the bonding agent and allow to dry. Mix up enough pre-mix marcite. This stuff sets up in about 3 to 5 minutes so work quickly. Use a sponge or trowel to smooth the surface. That's it. For cracks. Grind the crack 1/2 to 3/4 inches and repeat the above steps.
That depends on the construction and finish of the pool.
Marcite is a thing of the past, at least here in Florida. It used to be a good product, but after the removal of asbestos, it does not last as long as before. The quaztz aggregate finish replaced marcite. Instead of use of marble,like in marcite, it uses quartz. Diamond Brite is one of many brands available. Then you have hydrazzo which is a kind of marcite with a twist; it is polished after finished to a glassy feeling. Pebble finish is also available; it is a little bit rougher than quartz aggregate finish. The latest thing for pool finish is the use of glass beads(beadcrete). Premium Pool and Pavers, Tarpon Springs, Florida 727 271 5975.
Marcite was the material used to finish the interior of a concrete swimming pool. It is in simple terms a mixture of crushed marble and white cement mixed with water to form plaster which is then applied to the pool floor and walls with trowels to provide a smooth finish for the interior of the pool . These days we use what are known as exposed aggrigate materials to finish pools which contain man made quartz such as Diamond brite. Any further questions. you can reach me here.. diamondbritepools.com
Marcite is a "plaster" made from marble dust and white cement. It's put on top of the gunite and gives the pool a smooth finish and bright luster.
Cannot be answered without further information. What is the adhesive? Are you under water or dry? Is it a tile or marcite surface? Please asvise
If your pool has a marcite finish, it is quite simple. Not easy, but simple. It can be completely polished with a diamond pad and a hydrotorque machine. A service like this should cost you around $600. It depends on the size of your pool. This procedure will make your surface feels glassy, extremely smooth. Premium Pool and Pavers, Palm Harbor, Florida 727 271 5975.
For marcite or plaster finish - Acid Wash. Google "acid wash" . Also Pumice stone will srub off black or green algae.
Jacks Magic has many products for pools. Which one???
plaster can NOT be pacthed but vinyl you could patch them with a kit but otherwise you have to buy another pool
It's better to patch over a pool patch than to try to rip or scrape it off. If it will pull up easily with your fingers, then you can remove it.
No, but you can buy a cheap patch kit at pool stores or other places to easily patch above ground pools.
Yes, pool companies sell "Under Water Cement" and patch kits. If you hole is bigger than the usual patch, ask the pool company to sell you a piece of used liner.