0
You don't say if it it the blade or Tranmission drive belt. Get a piece of new carpet remnants and spend about twenty minutes laying on it while you study and inspect the under carriage of the mower. Ideally -jack the mower up to eye level and remove the cutting deck retainers to drop it down one foot to a work bench or platform. Loosen the blade belt keeper post bolts on the deck and main frame to allow removal of the old belt an installation of the new belt. Reposition the keepers and tighten bolts.For the Transmission drive. Remove the cutting deck from the mower. Press the clutch and tie it to the floor.Remove the bolts from the left and right belt keepers at the chassic motor pully. This is as far as I got. It is not simple to get that new belt in there but hopefullt this week I will get er done and report back.
Easiest way I found is to hold up the rear of the tractor with a come-a-long/rope with wheels off the ground,remove both wheels,remove everything holding the rear end in place leaving the 2 back bolts in "loosened to the max" that hold the tranny to the frame,remove clutch pully,remove steering snap ring and pull the steering wheel up out of the way,remove the old belt and replace with a new one,repeat steps backward to finish the job.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
How do you fit drive belt on Murray ride on mower?
We will need some more details... Is it the drive belt or the belt for the blades?it is the drive belt for Murray lawn mower model 38618x92a
What is the long belt from mower to transmission?
The belt from the mower engine to the transmission would be called a drive belt.
The illustration on the drive belt routing on your john deere gt225?
i need diagram on how to replace deck belt on John Deere GT235 mower
What is the drive belt size for a Murray 12-36 ride on mower?
its 1/2" x 83" inch od
Why won't my Murray riding mower stop after the drive belt was changed?
I believe it has to do with the main drive belt. (The brake on these types of mowers are almost useless.) If the main drive belt is to short it engages the slip pulley that drives the transmission. I replaced an original belt that was bad with a replacement that was about an inch shorter and my mower would not stop. Replaced the belt again with the exact size required and problem solved ... BUT ...About a month later the same thing happened. The mower would not stop when i released the drive pedal and i ruined my transmission "snapping it out of gear to stop the mower. Now i suspect it may be a worn "slip pulley" causing the main drive belt to ride closer to the spindle on this particular pulley, this , I believe , will cause the pulley to turn faster thus engaging the transmission. This pulley is similar to an adjustable type but it "slips" . On my Troy Bilt it is located in the rear right over the transmission. Hope this helps someone because i have spent hours trying to solve this problem.
What size belt goes on a Murray Riding Lawn Mower - 12.5 HP 40 Cut Lawnmower?
what size belt do i need with a murray riding lawn mower that is a 12.5hp. 40"
How do i Change belt for blades Murray riding mower model 40907X20A?
I changed the blade belt on my Murray mower. Now one blade stops and goes. If I lower the deck the blade stop . What did I do wrong?
Why does the mowing belt jump off on a 42 Murray riding mower?
Belt is stretched or the tension pulley
How do you install belt to mowing deck on 42 cut Murray 15.5 riding lawnmower?
I have Murray 42" cut riding mower that the belt came off. How do I put the belt back on?
How do you change a drive belt on a Murray ridding lawn mower?
Take it to the store that you bought it in and ask a member of staff to replace the belt for. If possible, try find the member of staff that sold it to you in the first place.
How do you replace a drive belt on a 38yard machine lawn mower?
How do you replace a mower deck belt on a stx38 hydro
Does anyone have a picture or diagram on how to put on a belt on a Murray riding mower?
According to Youtube
