If motor grunts and does not move, verify that regulator is not binding. WIRING VOLTAGE TEST The following wiring test determines whether or not voltage is continuous through the body harness to switch. (1) Remove the master power window switch and bezel assembly from the driver door. Refer to Group 23, Body for proper procedures. (2) Disconnect wire connector from back of power window switch. (3) Switch ignition ON position. (4) Connect the clip end of a 12 volt test light to Pin 13 in door harness connector at the window switch. Touch the test light probe to Pin 9 and then to Pin 11. †If the test light illuminates, the wiring circuit between the battery and switch is OK. †If light does not illuminate, check the 40 amp fuse in the Power Distribution Center or for a broken wire. †The power window motors are protected with Positive Temperature Coefficient (PTC) device that prevents motor burn out. Check Junction Block. †Refer to Group 8W, Wiring Diagrams for circuit information and component locations. REMOVAL AND INSTALLATION POWER VENT WINDOW MOTORREMOVAL (1) Disconnect battery negative cable. (2) Remove D-pillar trim panel. (3) Disconnect wire connector from power vent motor. (4) Remove nut holding crank to vent glass. (5) Remove bolts holding power vent motor to D-pillar (Fig. 4). (6) Remove power vent motor. (7) Pull the crank system from the motor. INSTALLATION Before installing crank, cycle replacement motor to the open position. Install crank hinge in extended position to the motor and for installation, reverse the above procedures. POWER WINDOW SWITCH To remove power window switches refer to Group 23, Body for proper procedures. POWER WINDOW MOTOR WARNING: DO NOT HAVE ANY HANDS OR FINGERSIN SECTOR GEAR AREA WHERE THEY CAN BE PINCHED BY SMALL MOVEMENTS OF REGULATOR LINKAGE. REMOVAL (1) Tape the window in its existing position to remove its weight from the regulator system. (2) Cut and remove the tie wrap at the window motor. Its no longer required. (3) Disconnect window motor wire connector from door harness. (4) Remove screws and nuts holding window motor to the inner panel. (5) Remove the motor from the door inner panel, let it hang from the cables. (6) With the cables still attached to the failed motor, Install the replacement motor to the door inner panel. Tighten down the screws and nuts to 3.4 to 4.5 N·m ( 30 to 40 in. lbs.) of torque. (7) Separate the failed motor from regulator by: †Removing the drum cover plate. †Lift the cable guide off the motor, the drum with cables, will be lifted off simultaneously (Fig. 5). CAUTION: Do not allow the drum to separate from the cable guide, by dropping drum or letting the cables unwind. INSTALLATION (1) Install the cable guide and drum into the replacement motor.
About 1500
It cost me $2600 in Healdsburg California.
how much should a minivan battery cost to replace 2008 Chrysler Town and Country
It depends on the make and model of the minivan.
Replace the gauge. This problem indicates an un-repairable failure inside the unit.
Open rear hatch, look at tail light lens, there are two screws in it, take them out, the lens will come out, twist the socket to release it replace bulb. I suggest using some dielectric grease in the socket while you are at it, might save trouble down the road. AJ
Truck, no. Car or minivan, yes.
If it is a plastic radiator and it is stripped, no, if it is metal yes.
How do you replace the clio front passenger seat cable
Open the hood. You may need to make some extra room behind the headlight assembly. Grab the retaing ring and turn it. Then remove the head light but save the ring and unplug the wires. IMPORTANT NOTE: Do not touch the glass part of the new head light. How do you change the headlamp assembly on the passenger side of a 1994 Town and COuntry van, not the light bulb itself, the entire assembly?
how do u replace passenger armrest on 2007 Chevy conversion van
Need the instructions to replace passenger side mirrow on a 2006 Saturn vue.