0
To avoid setup time violations:
- The combinational logic between the flip-flops should be optimized to get minimum delay.
- Redesign the flip-flops to get lesser setup time.
- Tweak launch flip-flop to have better slew at the clock pin, this will make launch flip-flop to be fast there by helping fixing setup violations.
- Play with clock skew (useful skews).
To avoid hold time violations:
- By adding delays (using buffers).
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
Why does a screw hold better than a nail?
because the threads hold them into place while as a nail works its way out at a point of time !
What is the function of zero order hold?
Zero order hold is used in Digital - Analogue converters (DACs). It literally holds the digital signal for the sample time, then moves to the next digital sample and holds that signal for the sample time as well, in order to reconstruct the analogue signal.
What does the RIP hold-down timer do?
Instructs routers to ignore updates, for a specified time or event, about possible inaccessible routes.
Describe the response of a capacitor when connected to and then disconnected from a battery?
A capacitor that is suddenly connected to a battery will charge to the battery voltage. The time to do this is dependent on the current capacity of the battery and wiring, and the capacitance of the capacitor. This represents an instantaneous short circuit, which lasts for a (usually) very short time - but damage could be done if there was no resistance. A charged capacitor that is suddenly disconnected from a battery will hold that voltage. The length of time it will hold is dependent on how much leakage current there is.
In the setup function of Arduino how do I average 50 readings to determine ambient light level and save the average voltage in the variable Vref?
You can use a FOR loop to loop 50 times, add the reading to a variable and then divide by 50 after the loop completes to determine the average. Make sure that you use a variable type large enough to keep the total. Keep in mind that unless you put a delay in the loop the 50 readings will be taken very fast and will probably vary little. You need to consider what a reasonable time to measure to determine what a good average would be, and then add a delay to give you the right period to take the average over. For example, if you want to take the average over 5 minutes (300 seconds), you would need to add a delay(6000) 6 seconds) to stretch it over the measurement time. Keep in mind that your main program loop won't start until the setup process is complete, so in this example the setup process will take five minutes.
What is the difference between flipflop setup time and hold time?
Flip-flop setup time refers to the minimum amount of time that the data input must be stable before the clock edge for the flip-flop to correctly latch the data. Hold time, on the other hand, refers to the minimum amount of time that the data input must be stable after the clock edge for the flip-flop to correctly store the data. In summary, setup time is the minimum time before the clock edge, while hold time is the minimum time after the clock edge for proper operation of the flip-flop.
Is squid a web browser cache?
It is a proxy. But can be setup to cache a set amound of data. For instance you can setup the cache to hold 500Mb. And if you goto Google it wont have to load the images every time...
Technically squid is a web browser cache?
It is a proxy. But can be setup to cache a set amound of data. For instance you can setup the cache to hold 500Mb. And if you goto Google it wont have to load the images every time...
What is meant by setup time?
The setup time is the time that the data inputs must be valid before the clock transition.
Which backup site would require NO setup time at the occurrence of an emergency Which backup site would require NO setup time at the occurrence of an emergency Which backup site would require NO setup?
Mirrored
What are the cost drivers which are used in apportioning overheads cost under activity based budgeting?
Cost drivers are activities due to which cost incurred for expample as many time as machines are setup for production as many time machine setup cost will be incurred so matchine setup is cost driver.
What are the human rights violations and genocide of world war 1?
it was the time
WHAT account setup if you do not have time to finish an account setup task what can you do to save your work?
Click the File for Later button
During account setup if you do not have time to finish an account setup task what can you do to save your work?
Click the File for Later button
What is an pear-shaped flask and how is it used?
It is used in setup with filtration and distillation happening at the same time. Anti bumping granules and the solution are place in it to avoid solution being "bumped out" of the flask during the filtration and distillation process
In what section do you usually find date and time setup in CMOS setup utility?
In EVENT VIEWER, commonly found in SiSoftware Sandra
What does setup mean?
An experimental setup is one that is done as a test or experiment to see if something works. These are done in business all the time.
