if the drain is broken or wont drain, you have to jack hammer it up and replace p trap and pipe, then pour concrete and then do tile..Is that what u wanted? If you want to know about how the pipe itself is installed, it would be easier to go to Home Depot and just look at one of the how to books.
If you have a drain available. You may need to chip some concrete around the drain to install the bottom half of the drain. With that in place, set the shower over it and the top piece screws into the drain to form a seal. You can build a 2x4 frame and raise the shower up enough to run a drain to a sump or a floor drain.
The item used under the shower pan to create the slope for the drain is called a "shower pan liner" or "shower pan membrane". It is typically made of PVC or CPE (chlorinated polyethylene) and is installed over the subfloor and around the drain to create a waterproof barrier. The liner is then sloped towards the drain using a combination of techniques, such as sand or mortar beds, pre-sloped foam panels, or adjustable slope systems. The choice of method depends on the specific requirements of the installation and the installer's preference. Once the liner is in place and sloped properly, the shower pan can be installed on top of it, and the tile or other finish material can be applied. Proper installation of the shower pan liner is crucial for ensuring that water drains properly and does not seep into the subfloor or surrounding areas, causing damage or mold growth. HydroBlok systems are known for their durability, water resistance, and ease of installation. They can be used for both residential and commercial applications and are suitable for a variety of finishes, including tile, stone, and vinyl.
typically shower drains are 2"
Yes, but you should you use an adhesive that is ductile
2"
tile should slope sightly down toward the drain and drain should be recessed slightly below the top of the tile
The center of the shower floor where the tile shower drain would normally be positioned ... drain base. After this step the sloped mortar bed should be ... pan liner or membrane in our instructions.
Around $14,890 including tile work and filing fees
form_title= Shower Tile form_header= Redo your shower tile and create a whole new bathroom look! Do you have tile that needs toe removed?*= () Yes () No () Not Sure What color tile do you what installed?*= _ [50] What are the dimensions of your bathroom?*= _ [50]
With tiles! But on a more serious note, build a frame, plaster board it, get a base tray for the water to fall into and connect it to your waste. Plaster the "boarded wall" then tile it. Then install the shower itself. Seal up then its ready to use.
If you have a drain available. You may need to chip some concrete around the drain to install the bottom half of the drain. With that in place, set the shower over it and the top piece screws into the drain to form a seal. You can build a 2x4 frame and raise the shower up enough to run a drain to a sump or a floor drain.
The shower may be leaking from: 1) A failure of the drain and associated piping itself (e.g., corrosion of the cast iron floor drain), 2) A failure of the shower pan, which is an ostensibly waterproof liner (may be metal or synthetic polymer) embedded in the tile floor (or comprising the plastic floor) which is mechanically connected to the drain; or 3) Leakage of water in the shower's surrounding area (walls, non-pan floor area, etc.) which is accumulating and dripping near the drain.
It shouldn't be that hard. Here is a good site that shows step by step. http://www.diynetwork.com/how-to/how-to-build-a-tile-backsplash-for-the-shower/index.html
I would tile up to the pan where it sits. If you remove it, you will have to tile completely under it so it stays level and raise the drain. If it is in the basement or or over a finished ceiling this can be a problem. If there is a vanity, I would remove it and tile under because is is much less hassle and gives a better result.
The best way is to dry the tile after you get out of the showe to avoid build up and water spots. They do also make after shower sprays that you can use to help keep mildew ans water spots under control. anonymous@oola.com
Shower drain goes into a trap under shower. Continue piping from trap to drain line.
Water won't drain from shower. Either trap or shower drain line is clogged.