answersLogoWhite
Headlights Tail and Brake Lights
Dodge Intrepid
Ford F-250

How do you change a tail light assembly for a 2001 Dodge Intrepid?

192021

Top Answer
User Avatar
Wiki User
2008-08-13 10:54:02
2008-08-13 10:54:02

if entire left of right assembly, unscrew the 3 plastic wings nuts behind assy inside the trunk, pop out, disconnect harness

1

Related Questions

User Avatar

A 2001 Intrepid does not have an oil change light.

User Avatar

Trunk light switch is part of the trunk light socket assembly...

User Avatar

in the trunk there are 3 plastic wing nuts take them off and the light will come out.

User Avatar

It is very easy to change the license plate bulb in a 2001 Dodge Intrepid. You will need to remove the tag and then unscrew the light cover. After the cover is off, unscrew the light and replace with a new one.

User Avatar

From outside,take a screws out to get light assembly loose and remove light socket from back of assembly and channge your light bulb,then put it back.

User Avatar

you have to remove the headlight assembly 3little bolts

User Avatar

on all dodge trucks the way you change the bulbs is simply unscerew the tail light assembly and remove it from the rear of the vehicle and you will see your lightbulb fittings right on the back of the light assembly

User Avatar

Inside the trunk there is a turnable thumb screws where the brake lights are. Twist screws off and the brake light pops out.

User Avatar

With the hood up look at the outer end of the Headlight, You will see what looks like a snap together piece. wiggle the corner light and this will help you to see the clip that has to be moved in order for the light to slide out so you can change the bulb...I myself just put new headlights in my 96 dodge intrepid.

User Avatar

You just have to pull back the trim in the trunk to access the fasteners for the taillight assembly. Once you remove the taillight assembly just replace the bulb.

User Avatar

From inside the trunk you remove the three or four finger nuts to remove the entire taillight assembly. Once you get it removed you'll see the light plugs on the backside.

User Avatar

On my 2005 Dodge Ram Daytona. I had to open the tail gate, remove the two screws on the jam next to the light assembly. After removing the assembly, there is a light bar held by six screws. After removal of these, you can select the bulb you wish to change and then reassemble to install light assembly.

User Avatar

This has been answered in other post in this series, but its easy. Open the trunk and unscrew 3 black plastic wing nuts that hold the tail light assembly onto the car. You have to take all 3 nuts off, the light assembly will come loose, then just twist the correct light socket 14 turn off and change the bulb. 2 of the nuts are easily seen the 3rd one is up in the top corner.

User Avatar

The airbag computer has detected a malfunction and set a code.

User Avatar

I believe it is 2 torx screws inside the tailgate holding the assembly. Have to replace the whole assembly.

User Avatar

there are two tourqu screws one on each side undo thes and slide out light then release the clip on the bulb from the back side and slide out the bulb

User Avatar

i have dodge intrapid 2.7l my 02 sensor light come on p0051

User Avatar

how to turn off engine light on 2002 Chrysler int

User Avatar

There are three black caps that screw off in the trunk behind the brake light itself unscrew them and the assembly comes out then change bulb

User Avatar

open the trunk. move the trunk liner where the tail lights are. you'll see 2 plastic screws. unscrew them. there is a 3rd screw, you have to reach up to it, its towards the top corner of whatever side you're on. disconnect the wiring remove light assembly

User Avatar

You may need to replace the power control module.


Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.