there are two pins located behind the headlamp assemblyon the metal brace behind it. just remove those, and the whole assembly comes out. you can then take the bulbs out. you will need to realign the assembly though. all this is mentioned in the owner's maual if this didn't help. manual shouldn't be expensive to buy. look on eBay for those.
Passanger Side and Drivers Side Bulb Changes
There are two keepers just behind the grill, between the grill and the battery on the passenger side. These keepers look like little flat tabs that stick up, just pull them up and take them off and then the whole assembly will fall out. The only thing holding the assembly in place are the two tabs that hold the top of the assembly and two tabs that hold the bottom. The bottom two tabs just slide in. When you look at the drivers side, that assembly fits the same way.
I had never disassembled the headlight assembly before and it took me about 45 minutes to figure it out and change the passenger side bulb, after being led astray by the kid at O'Reilly's. The second bulb, on the drivers side, took about 5 minutes.
You don't need any tools to change the bulbs.
You change out the starter on a 2001 bravada by opening the hood of the car then following the battery redÊcable from the battery to the starter.
behind fusebox drivers side
look in your manual
back of assembly and twist.
If you cant get to it from the front, you will probably have to look from the back and see where the wires connect to the back. Then you should be able to unscrew the fixture from the plastic and replace the bulb.
Pump is in tank; filter is on frame under car under drivers seat.
Change the whole headlamp bulb. Should be a H4.
See posting for "How do you change the headlamp bulb in a 2003 Grand Prix?" All these model years are similar in production for the headlamp assembly.
Here's the answer: http://www.wikihow.com/Change-Headlamp-in-Chrysler-2001-Town-and-Country And here is my music: http://woundedego.com And here is my book: http://bibleshockers.com And here are my politics: http://billrosspolitics.bibleshockers.blogspot.com Have a great day and good success.
There are none
Is it a Beetle ? if it is a beetle open the hood . locate headlamp. Next to headlamp unit undr hood is a hook or half hook shaped ring . unlock the tab under the hook and push hook downwards to release the headlamp unit . once removed unplug unit . remove back cover on headlamp. replace defective bulb . to reinstall headlamp line up ythe rails on the headlamp unit aNd push headlamp back into housing . make sure locking ring is engaged fully .
The fuel pressure regulator is on a 2001 Bravada is located in the rear on the gas tank. It is in the fuel line between the fuel pump and the gas tank.
With the hood open remove the (2) two headlamp assembly bolts from the upper fascia support. Slide the headlamp assembly outward enough to release the headlamp bracket tabs from the slots in the upper fascia support. (to release the tabs from the slots on the passenger side lens move the assembly to the left when facing the engine, and when doing the drivers side lens shift the assembly to the right ) Position the headlamp assembly away from the vehicle body to access the electrical connector. Disconnect the electrical connector from the headlamp assembly. Remove the headlamp assembly from the vehicle. If you wish to change the halogen bulb: Disconnect the electrical connector from the headlamp bulb/socket. Remove the headlamp bulb/socket retainer ring from the headlamp, by turning counterclockwise. Remove the headlamp bulb/socket from the headlamp assembly. . "G" These instructions are similar from around '96 to '03 grand prix model years all trim levels.
1999 GMC Jimmy Envoy 2001 Chevy Impala 2001 Ford Escape 2003 Mercury Grand Marquis 2002 Oldsmobile Bravada 1996 Oldsmobile Bravada 2000 Chevy Venture 1994 Kawasaki Vulcan 1500
pull up on the two white plastic tabs behind headlamp assm. and pull assm. out.
In the distributor .
I have a chevy 2001 ls tahoe. How do you access the drivers side door speaker to change step by step.
I went to a web site http://home.comcast.net/~slashpub/ and found clear directions including pictures. It is not easy, but it can be done. Good luck.
it is an easy job but hard to explain. If you go to an Autozone store they will install it for you if you buy the piece there in about 3 minute.
its in the owner's manual. usually with pictures.
Open the hood, remove the pins holding the headlamp assembly, remove headlamp assembly, now you can reach in and remove the day time bulb socket assembly to replace the bulb. Repeat procedure on other side.
next to the egniton
1997-2001, remove the 2 screws holding the plastic headlight bezel. Remove the bezel. Located the 4 screws on the metal frame holding the headlamp in the headlamp bucket. Remove them and the headlamp will be loose. Unplug the wire harness. Reassemble all of the above.
Its in the fuse block - underhood.......