answersLogoWhite
Chevy Tahoe
Nissan Xterra
Late Model 1979-New Ford Mustangs

How do you change out a passenger side mirror on a 1996 Ford Mustang?

161718

Top Answer
User Avatar
Wiki User
2011-09-13 00:15:08
2011-09-13 00:15:08

1.First get a small screw driver or blade. 2.The separate part where the arm rest is where the window switch is, you need to pop that out, (there is a really small divet there i didn't see it at first but now that i know its there its obvious) there is a clip on the top of it to the right. Pop the clip out and gently pull up until the rest of the handle armrest is out. 3.There are two screws underneath there. 4.By the hinge of the door at the bottom by the speaker there is a black plastic button screw pull this out. 5.Now at the part where the mirror is connected (you should obviously see this part right next to windows on the top) you can push that black piece to the right and pop that off. 6.Now lift up on the door panel and pull towards you. the door panel should easily slide off. 7.Now undo the 3 screws holding the mirror on, unconnect power cable if you have power mirrors. 8.Now just put it back together the same way you took it apart. ^^

1

Related Questions

User Avatar

remove interior left corner cap--then remove 3 screws and then remove mirror--->reverse procedure to put back new mirror...u r almost a technician

User Avatar

Yes , one for the driver and one for the front passenger

User Avatar

bank 1 - is the passenger side of the engine on your Ford V8

User Avatar

How much does it cost to replace a passenger side mirror on a 1996 Camary. The whole Mirror broke off. Answer I don't know how to fix one. I wish I did, I think I am going to have to buy one.

User Avatar

back of the engine towards the firewall, should be on the passenger side

User Avatar

The 1996 Ford Mustang GT was rated at 215 horsepower

User Avatar

I have a 1996 thomas 50 passenger with a wheel chair lift that weighs 31000 and some change.

User Avatar

The 1996 Ford Mustang GT was rated at 215 horsepower

User Avatar

Transmission Modulator 1996 ford mustang can not find location

User Avatar

You first need to remove the triangle shaped trim piece inside the door opposite the mirror. It just pries out with a screwdriver. Then disconnect the electrical connections if a powered mirror. Undo the 3 bolts holding it and then remove the mirror. -RC-

User Avatar

On a 1996 Ford Mustang : The automatic transmission fluid level dipstick is located in the engine compartment , near the firewall , on the passenger side of the engine in the engine compartment ( use a funnel )

User Avatar

According to the 1996 Ford Mustang Owner Guide : With engine oil filter change : The 3.8 liter V6 engine takes : ( 5.0 U.S. quarts , 5W-30 is the PREFERRED oil )

User Avatar

The 1996 Ford Mustang owners manual shows : WITH FILTER CHANGE 3.8 L - V6 engine - ( 5 quarts ) 4.6 L - V8 engine - ( 6 quarts )

User Avatar

The 1996 Ford Mustang owners manual shows : for the 4.6 L ( 2V ) with filter change 6 quarts / 5.7 liters oil dipstick is used to determine oil capacity

User Avatar

( bulb # 168 ) for a 1996 Ford Mustang license plate light

User Avatar

No, they are different body styles.

User Avatar

There is no 5.0 engine in a 1996 mustang. 96 is the first year of the 4.6 engine.

User Avatar

The 3.8 liter V6 engine in a 1996 Ford Mustang has a timing CHAIN

User Avatar

Go to this website. It will show to take off the door panel and the side mirror. http://www.kwmuth.com/techsupport/pdfs/21000170.pdf

User Avatar

Remove the inside door panel. There are three bolts with nuts & washers that hold the mirror onto the truck. If your windows are manual, the crank level will need to be removed.

User Avatar

Remove the door panel. Towards the front of the door there are two screws holding the mirror on. Inside the door are two connectors that connect the mirror wires to the door. I have a 98 and if it is the same process that's all you need to do.

User Avatar

How to remover 1996 ford mustang radiator fan from the radiator motor

User Avatar

The 3.8 L - V6 engine - in a 1996 Ford Mustang is 232 cubic inches

User Avatar

The 3.8 liter V6 engine in a 1996 Ford Mustang is rated at : ( 150 horsepower from the factory )


Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.