0
1 Disconnect the negative wire to the battery. I did this to be safe.
2 Disconnect the oxygen sensor from the air intake. Do not pull from the wires only pull from the boot. Be careful not to break the sensor either
3 Pull the tube connected to the left side of the air intake off then remove the air intake.
4 Disconnect the map sensor and all other electric components that are attached to the manifold
5 Disconnect the cable that is connected to the throttle body (you do not have to take the throttle body off of the manifold to do this).
6 On the left hand side of the manifold there are 2 manifold support brackets loosen them up but do not take them off. When they are loose just pull the top part of the bracket that is connected to the manifold back and off the screws. .
7 On the right hand side of the manifold there is another support bracket that is connected to the throttle body. First take off the screws then where the support bracket connects to the cylinder bellow the manifold loosen the two bolts until you are able to slide the bracket out of the way.
8 On top of the manifold there are six bolts unscrew them.
9 Important! Before you remove the manifold to get to the spark plugs be very careful and remove the manifold by lifting it straight up and then pull it towards you slow. The reason for this is because there is a valve connected to the manifold directly in the back that you do not want to break. The tubes that are connected are long enough so you can take the whole manifold and place it to the right just out of the way so you can get to the spark plugs. (before changing the spark plug it is recommended that you take compressed air and blow away the dirt surrounding the spark plug area. This is done so that no dirt gets into the combustion chamber when you remove the spark plug.)
10 Once the manifold is out of the way disconnect the electric connectors that are attached to every spark plug. Pull them from the boot of the connector.
11 Repeat for all spark plugs - Unbolt the spark plug tube then pull it straight out and then with the spark plug socket unscrew the spark plug and replace it with a new one.
12 After the spark plugs are in on the left hand side of the engine in the back you will see a tube that says pcv. Remove the tube from the engine and unscrew the valve and replace it with a new one.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Does a dodge charger srt8 have 20 spark plugs?
The Dodge Hemi's have 2 spark plugs per cylinder which equals 16 spark plugs
How many spark plugs dodge charger 3.5 liter?
6
How many miles change spark plugs dodge charger 5.7 hemi?
Owners manual says every 30,000.
Does a 2007 dodge charger have 6 spark plugs in the 3.5L v6?
yes.
How many spark plugs does a 2007 dodge charger have?
16, two per coil
Where are the spark plugs in a 2008 dodge charger?
They are under the coils, on top of the valve covers.
When do you change the spark plugs on 2006 charger sxt?
100,000 miles.
How many sparkplugs are needed for a 2007 Dodge Charger RT?
The hemi has sixteen spark plugs.
How do you replace spark plugs on a 2006 dodge charger 3.5?
You have to remove the intake plenum. It just unbolts.
Where are the spark plugs in a 2007 v6 dodge charger 2.7 automatic?
look in the owners manual for that info.
Are coil over plugs ever changed in a 2008 dodge charger?
The coil packs: only if something goes wrong, they are not a 'wear item,' and therefore have no anticipated change timeframe The spark plugs: yes.
How do you Change spark plugs on a 5.9 2002 dodge ram 1500?
To change spark plugs on a 5.9 2002 Dodge Ram 1500, locate the old spark plugs. These are located at the end of the 8 wires inside the vehicle's bonnet. Remove the old spark plugs and replace with new.
