answersLogoWhite

0


Best Answer
Windstar Safety Recall -

Ford has issued a safety recall that can be directly related to the ABS modules and brake fluid leaking into the wiring harness that controls it.


Read the information at the "Related LINKS" below for much more about this recall.



Answer

Removal

Prior to removal of module, it is necessary to upload module configuration information to a scan tool equivalent to Ford's NGS,WDS, or PDS. This information needs to be downloaded into the new module once installed.

Disconnect the battery ground cable. Raise and support the vehicle. Remove the hydraulic control unit (HCU) dust shield,located directly uder the driver's door area fastened to the subframe.

Disconnect the anti-lock brake control module electrical connector. Slide the connector lock rearward.

Remove the three HCU bracket to frame bolts.

Lift the bracket hooks from the frame and lower the HCU to access the anti-lock brake module.

Be sure to lift straight up to avoid damage to the HCU components.

Remove the anti-lock brake module. Remove the bolts.

Installation

Once the new module is installed, it is necessary to download the module configuration information from the scan tool into the new module.

NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 miles) or more to relearn its strategy.

NOTE: Clean the top of the HCU before installing the new module.

NOTE: Clean the harness and module sides of the electrical connector before connecting.

To install, reverse the removal procedure.

User Avatar

Wiki User

โˆ™ 2009-12-20 16:06:20
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: How do you change the ABS control module on a Ford Windstar?
Write your answer...
Submit
Related questions

Where is the ignition module on a 1999 Ford Windstar?

If you're looking for a stand-alone ignition controlmodule, there isn't one on the Windstar.This job has been transferred to the Powertrain Control Module (PCM) and its direct control of the coilpack.


How to Change wiper timing control module Ford Focus?

How do you change the wiper control module on a 2006 Ford Focus


Where is the constant control relay module on a 96 ford windstar 3.8?

Its beside the rad. on the drivers side


Where is the ignition control module for a 1995 ford windstar?

There is not a stand-alone ignition control module in the Windstars.Ignition control is fully handled by the Powertrain Control Moduel (PCM).See "Related Questions" below for more


What is ABS box in a ford windstar?

This could be referring to the ABS control module.See "Related Questions" below for more


Where is the airbag control module located in a 2001 Ford Windstar SE?

Airbag control module is bolted to the floor on a non-removable stand just to the right of the accelerator pedal behind the storage bay panel.


How do you change transmissions in the 1995 ford Windstar?

how do you change a shaft soleniod in a ford windstar 1995 v6 3.8 engin


Where is located the sensor for the door opener on ford windstar 2002?

electronic module


Where is the transmission control solenoid in your 2000 ford windstar?

where is the tcm in a windstar 2000 located


How do you change the idle on a 2004 Ford Explorer?

The idle is controlled by the powertrain control module ( computer )


99windstar temperature control?

heater windstar ford


How do you turn off traction control on 2000 Ford Windstar?

You can switch the traction control system off using the switch to the left of the radio on a 2000 Ford Windstar


Where is the location of the ignition control module on a Ford Focus?

You can find the Ford Focus ignition control module beneath the drivers side dashboard. The ignition control module will be above the accelerator pedal.


How do you replace the GEM module on a 1996 Ford Windstar?

The GEM in a ford windstar is located up inside the dash, above and to the left of the gas pedal. it's held in with a single bolt.


What is a Ford Gem Module?

The Gem Module is a relay that control the majority of the electrical functions in late model ford vehicles


Where is the speed control device located on a 1995 ford windstar?

The speed control device or speed sensor on a 1995 Ford Windstar is located on the transmission. It is a plug in just behind the bell housing.


Ford Windstar 1999 tail lights stay on all the time?

It sounds as if there is a problem with the rear electronics module in the Ford Windstar. This controls the front and rear lights and it is located in the back in the cubby with the jack.


How do you find and replace an actuator for a 1999-2003 ford windstar lx climate control switch?

electric window binds on 2003 ford windstar


Where is airbag module located on a 2008 Ford Escape?

where is the restraints control module located on an 08 ford escape hybrid


What is a PCM on a 1987 ford?

"Powertrain Control Module".


Where is the ignition control module on a 1994 ford explorer?

From 1991 to 1995 with the EEC-IV system there is an external ignition control module mounted on the radiator support in front of the battery. Remove the battery in order to change the module. 1996 and newer with the EEC-V system, the ignition control module is incorperated into the powertrain control module (PCM) that is visible from the engine compartment, in the firewall, on the passenger side.


Where is the ignition control module on a 1994 aerostar?

The 1994 Ford Aerostar ignition control module is located on the firewall in the engine compartment. The ignition control module will be on the drivers side of the firewall.


Where can you find a wiring diagram for a 2003 ford windstar rear electronic module?

Possibly here http://www.alldatadiy.com/


Where is the abs control module on a 1990 Ford Thunderbird sc?

The ABS Control Module on a 1990 Ford Thunderbird is in the electronics tray in the trunk. It hangs from the rear speaker deck.


Where is the body control module on a 2000 Ford Taurus - Mercury Sable?

The 2000 Ford Taurus body control module is located on the firewall in the engine compartment. The module will be on the passenger side, near the bottom, of the firewall.