Brake Pads and Rotors
Honda Odyssey
Mitsubishi Galant
Ford Expedition Eddie Bauer

How do you change the front brakes and pads in 1998 Mitsubishi Galant ES 4cyl 2wheel drive?

616263

Top Answer
User Avatar
Wiki User
2015-07-15 19:55:51
2015-07-15 19:55:51

1)Jack up the vehicle and put on jackstands 2)Remove the front wheels 3)Remove the 2 bolts in the back the the calipers, then hang the caliper with a clothes hanger on the spring or control arm (trailing arm on a galant if you want to get technical) 4)clean off everything 5)put the new rotors on the hub (note: tighten a lug nut over it so the rotor wont fall off) 6)replace the pads 7)reinsert the caliper and torque the 2 bolts to about 38 ft/lbs of torque 8)put the wheels back on and torque to 80 ft/lbs of torque 9)test drive it and listen for any abnormal noises

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Same as any other car. Eliminate the Mitsubishi Galant and this has probably already been answered.

User Avatar

In order change a transmission in a 2001 Mitsubishi Galant, it is best to change the solenoid first. it is then recommended that you take the car to a certified transmission garage to do the work.

User Avatar

how to change number 6 spark plug on a 2006 mitsubishi galant

User Avatar

how to change fuel pump on mitsibishi galant 2005 2.4 liter

User Avatar

The thermostat on a 99 Mitsubishi Galant is changed by draining the coolant, removing the upper radiator hose, and unbolting the housing. The thermostat can then be removed and a new one put into place.

User Avatar

A timing chain is designed to last the lifetime of the engine.

User Avatar

Is it like regular brakes are is there something special tool I need ?

User Avatar

When it is time to change the brakes on your 2001 Mitsubishi Montero, they will make noises. There could be a grinding or squealing noise that you will hear.

User Avatar

It is most likely your spark plugs and or wire set. All of this is easy to change. There is another forum that explains how to change your spark plugs for your Galant.

User Avatar

how do i chage my old breakes from my Mitsubishi gallant and put new breakes.

User Avatar

17mm wrench, oil pan, oil and jack stands or wheel ramps.

User Avatar

Safely jack the car up, remove lamps,replace bulbs.

User Avatar

you need to take the intake off to get to the back three plugs...

User Avatar

You must remove the entire intake manifold for you to have access on the three spark plugs located underneath it. it is advisable that a qualified Mitsubishi technician should do this.

User Avatar

remove intake manifoled to access back 3 plugs. time consuming but can be done

User Avatar

Its the black.......round motor that is at the back wall of your engine bay, could be on the drivers side,

User Avatar

open hood, find backside connector, turn quarter turn to remove connector to access lamp.

User Avatar

The computer in the car will not hold memory, the windshield washer only work on one speed, bright light will not work, I have to put the radio code in every-time I start the car. 2001 Mitsubishi Galant.

User Avatar

It's inside the glove box, you'll see two screws remove these and pull filter out.

User Avatar

there are 4 thick wires right on top o the engine take each out and u will see the plug


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.