0
How do you change the oil and primary drive lubricant on a BMW R1200C?
Wiki User
∙ 11y ago
There is no primary oil to change. The engine oil is changed by using a special cup type filter wrench. The filter is flush with the bottom of the engine. there should be an allen head drain plug for the engine oil.
to prevent old oil from being trapped in the oil coolers by the thermostat, change the oil cold after the engine was ridden for at least 30 min.
you can change oil hot too, but NOT just after a 2 minute run cycle. all this does is trap old oil in the coolers.
There is trans. oil to change as well as final drive fluid. The engine normally uses 4 qts. 20w50. the trans and final drive are best serviced with 75w140 synthetic gear oil. should take just over a quart to do both.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Can you drive your car after accidentally putting transmission fluid into your oil?
I would NOT DRIVE THE CAR. You can start it then change the oil immediatly. Transmisson oil is a great cleaner but not a very good lubricant for an engine.
How does car drive when low on lubricant differential?
not very far
What are some problems with the primary slave drive?
What are some problems with the primary slave drive?
How to change a secondary hard drive to a primary hard drive?
First partition, don't change anything about the jumpers. If your hard drive is set to master, it will stay master on that partition so it will only make the hard drive as you wish, ''" master or slave ''" .. Second.. Load the cable at the end of the cable will make master. Here's the deal how to 1 on your motherboard beside the ribbon from your hard drive the plastic cap with some pin in it it 1 say primary beside and 1 say secondary. Simply open your computer change the hard drive cable from the 1 hard drive to the other 1 hard drive. 1- The easiest way here is to open your case change your ribbon (40 pin) from one hard drive and change it to the other hard drive jumper configuration might be required simple manual easy to configure its a little pin on the back of the hard drive between the power connector and the ribbon tha plastic removable cap 2- If you have 2 hard drive on the same ribbon, those 2 hard drive will be set on the same thing so as primary u will have to get another ribbon plug into your computer board and put one hard drive to that new ribbon and it will make it secondary so the ribbon you have is your primary. 3- I hope you get it about the ribbon. One ribbon is your primary and the other is your secondary dont mess up. There is normally 2 plugs on 1 ribbon. Don't mistake by saying 1 plug is primary and the other is secondary. It's just a master and a slave that's it if you change plug from one hard drive to the other there you can talk jumper but you might need in order to work in your bios to change the startup hard drive on windows and also get to configure jumpers.
What is the primary respiratory drive for a patient with COPD?
Hypoxic drive.
How do you remove the primary drive chain on a Harley Sportster 883 to change the stator?
Take the rotor and the clutch basket off at the same time
How should the primary hard drive be listed in BIOS?
As the "primary master".
Is it ok to put WD-40 on an alternator belt?
Absolutely NOT! WD-40 is a lubricant. The last thing you want to put on a drive belt is a lubricant. If the belt is making a noise, it is either loose or worn out.
What are the primary reservoir drive mechanisms?
The primary reservoir drive mechanisms are (1) Gas drive which includes both solution gas drive as well as gas cap drive (2)Water drive (3) Gravity drainage and (4) Combination drive.
Is a computer hard drive a primary or secondary storage?
ram is primary Jake
How many primary partitions can be created on one hard drive?
four primary
What is difference between primary device and primary storage device?
A primary device would be the main system drive. Almost always a hard drive. A primary storage device might just be another way to refer to it.
