answersLogoWhite

0


Best Answer

The question you ask is tooinvolved for a proper answer. You may want to go to a car parts store, or book store, andget a repair manual for your car.They cost about $16.00Or, go to a Public Library.

Remove starter on a 1999 rodeo 3.2 v6 first this is no easy task you will need torches and air tools unless you really have ALOT OF PATIENCE ! Disconnect the + red post on battery. Jack up left side (DRIVER SIDE) secure vehicle with stands or blocking ! Spray the 3 bolts mounting the exhaust pipe to the manifold with a good pentrating oil.Unplug the 2 oxy. sensors on the pipe you'll be removing ( be careful not to break the clips on them) Get a thin sheet of metal cut it to fit up in front of fuel tank so no sparks can get on tank (GET A FULL FIRE EXTINGUISHER)( if you have a fuel leak you have to take care of that first!) after confiming there is no fuel or other combustibles in the area torch off the weld nuts on the rear side of the flanged pipe be careful not to damage flanges take a hammer and drive out bolts. Now move to the front of pipe room is limited i used several 3/8 drive extensions a swivel, 17 mm deep well 6 point socket with a 3/8 to 1/2 adapter hooked up to a 1/2 breaker bar.These nuts are selflocking tight little Bas*#% glow them with the torch be careful that the heat from your flame doesn't burn any wires or hoses! Key here is BABY STEPS heat it turn it heat it turn it after a full turn has been made heat it and hit it with the air rachet. You can now move the pipe down and back far enough to remove starter.Remove the 2 10mm bolts holding on shield. Remove the 2 14mm bolts holding starter to eng.for one you must slide wire loom out of the way to get on it. The starter wires one wire you must push down on top of connector to release it. the other wire is a 13mm i believe. Starter is gonna run about $150.00 Check gasket and flange area at manifold & gasket at flange at rear pipe. I applied red high heat silicone and reused mine. Used new nuts (Couldn't find flanged lockers just used regular mm nuts no washers) and bolts with neversieze. This should be done by a profesional ! LOL!

User Avatar

Wiki User

โˆ™ 2015-07-16 18:57:33
This answer is:
User Avatar
Study guides

Where I can purchase purchase HID Fargo ID card in Dubai

โžก๏ธ
See all cards
โ˜†โ˜…โ˜†โ˜…โ˜†โ˜…โ˜†โ˜…โ˜†โ˜…
No Reviews

Add your answer:

Earn +20 pts
Q: How do you change the starter in a 92 Isuzu Rodeo?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do you set the timing on a 92 Isuzu Rodeo 3.1?

How do you set the timing on a 92 Isuzu Rodeo 3.1?


Will a manual transmission for a 92 Isuzu rodeo fit a 95?

Yes if the engine's are the same


Does a 92 Isuzu pickup have a fuse to the clutch starter safety switch?

No


What do you do in a 92 Isuzu Rodeo when you get no fuel and no spark?

its your Pick-Up Coil in your distributor. I just dealt with this problem.


How do you change the clutch on a 92 amigo Isuzu?

i have u aswer but i dont exactly.....


92 Isuzu rodeo 2.6 02 sensor wiring diagram Lamp on unable to locate wiring diagram or controller box I need a wiring diagram of this Circuit?

call your local dealer and ask for the schematics for your Isuzu


Where is fuel pump located and how difficult is it to change in a 92 Isuzu Rodeo?

In the fuel tank. Just replaced my on a '91. Wasn't real difficult, have on jack to lower the tank and one to raise the body of the car and you can roll the tank out, change pump and roll it back under.


How much to replace a Clutch plate on a 92 Isuzu Rodeo?

The value of a clutch plate depends on whether it is new or refurbished. It can cost anywhere from 50 to 300 dollars.


How do you replace the speedometer light bulb on an Isuzu Rodeo?

that depends on the model year of the rodeo. If its a 92/93/94 remove the guage housing module(see how do i remove the dash board of a 93 rodeo) Once the module is out the front and rear panels of it will pop off with a screwdriver and you can replace the bulbs.


How do you change the starter on a 1991 Geo Prism?

Same answer as: "How do you replace a starter on a 92 Geo Prism LSI or GSI?" at this same site.


How do you locate and change the starter solenoid on a 92 Chevy S10?

The starter solenoid is located on the starter. It would be more cost-effective to have the entire starter replaced with a good remanufactured unit on this application.


How do you remove the starter from a 92 S10 blazer?

how to remove the starter from a 92 s-10 4x2 with a 2.8 engine

People also asked