Toyota Camry
Toyota RAV4
Toyota Tacoma

How do you change the starter on a 1990 Toyota Camry?

345

Top Answer
User Avatar
Wiki User
2007-02-22 17:23:00
2007-02-22 17:23:00

First, the battery needs to be disconnected...Safety first. Second, remove the electrical connector from the side of the starter. Third, remove the nut holding the ground wire (below connector). Fourth, remove the two bolts that hold the starter. Pull the starter away from the engine block. You may need to twist and turn it a little to get it around some of the wires and hoses. Install in reverse order.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

What kind of transmission fluid is used for a toyota camry 1990

User Avatar

how do i replace a power steering pump in a 1990 toyota camry?

User Avatar

The fuel pump on a 1990 Toyota Camry (4 cyl or V6) is located inside the gas tank.

User Avatar

how to reset oil timing on 1990 toyota

User Avatar

The Camry in 1990 doesnt have a shift solenoid. It was controled by a hydraulic shift governor inside the transmission. So the trans. has to come out and be opened up.

User Avatar

The 1990 Toyota Camry timing marks can be found on the main pulley on the front of the engine. The timing marks will be scattered around the outside of the pulley.

User Avatar

no. it not only wont bolt up but the electronics are entirely different.

User Avatar

If you are asking about engine oil, with a filter change about 5 qts

User Avatar

1990 Camry 4 cylinder thermostat is located off the bottom intake hose connected to the engine block.

User Avatar

I think that Camry disk brakes were very similar from 1990 to at least 1996, and I answered the question on changing brake pads for my 1995 Camry, so maybe that will help.

User Avatar

The horn relay can be found in the fuse box under the hood. The 1990 Toyota Camry horn relay is found in slot 12 and is rated at 10 amps.

User Avatar

The 1990 Toyota Camry transmission module can be found on the back of the transmission. The transmission module will be in the upper right-hand corner.

User Avatar

The same way you change the timing belt. the water pomp runs off the timing belt. It,s a pain in the butt.

User Avatar

two very good possibilities are the battery, and the starter. its easy to test, just try to jump start it. if it still just clicks it needs a starter. if it starts its probably the battery.

User Avatar

The intake air temperature sensor is located on top of the intake. In a 1990 Toyota Camry the air temp sensor assures the ECU the engine is running at optimal temperature.

User Avatar

There are a number of things that may cause a 1990 Toyota Camry to lose power. Some of the common things include adulterated fuel, spark plugs failure and so much more.

User Avatar

I have the same problem except I can't even find it, do you know how to access or location of the washer pump?

User Avatar

autozone.com has online manuals that have printable diagrams

User Avatar

I have 200,+ miles on the car. I change the plugs and wires yet it runs rough at idle and runs smooth at crusing speed. What can i do?

User Avatar

The starter motor is located below the intake and throutal body.

User Avatar

There is no PVC valve on the 4cyl Toyota Camry. รŠThe location of the PVC valve on the 6cyl is center upper engine area, mounted in the rear valve cover.

User Avatar

Possible lack of fuel pressure. Change your fuel filter first. Possible weak fuel pump.

User Avatar

they are entirely different. unless you are a really good fabricator and youre willing to change the entire wiring harness including the computer, dont bother.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.