0
take your belt off look on right hand side of motor if looking at motor should be close to bottom of motor 3 or 4 bolts will hv to take pulley
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Where are the timing marks on a 98 S10 22 cam sprocket?
The timing marks for the cam sprocket on a 98 S10 is on the front. The marks for the crank shaft is on the oil pump gear.
Torque spec on 1999 escort water pump housing?
15 to 22 ft./lbs.
What is the Fuel mileage 88 s10 2.8 engine?
I have an 89 s10 with a 2.8 V6. It gets about 22 city, 25 highway.
Rocker arm bolt torque for 1987 Chevrolet s10 pickup?
22 foot/lbs
What is the change in thermal energy of 1.9 kg of water that is brought to a boil from a temperature of 22?
620,48 kJ
What model number is a Remington 22 pump with a Pedersons patent January 5 1909 Serial number349044?
It is a Remington Model 12 .22 cal. pump
When was Pump It Up Fiesta created?
Pump It Up Fiesta was created on 2011-01-22.
Who makes rossi 22 pump rifles?
Rossi
What is the best 22 pump rifle?
Winchester and Browning
How do you align the oil pump gears on a 22 RE Toyota?
How do I align the arrows on the gears for a oil pump on a 1992 toyota 22 RE engine? wsbahr@gmail.com
What are the torque specs for the water-pump bolts-nuts on a 1983 22 R?
You can find that in the haynes manual at auto zone.Its kinda hard to find but have patience you will find it.
Water pump replacement in a 2005 chevy impala?
Water Pump Replacement (3.4L)Removal ProcedureDrain the cooling system. Refer to Cooling System Draining and Filling.Remove the drive belt shield bolt.Remove the drive belt shield.Loosen the water pump pulley bolts.Remove the drive belt. Refer to Drive Belt Replacement for the 3.4L engine.Remove the water pump pulley bolts.Remove the water pump pulley.Remove the water pump bolts.Remove the water pump (1).Remove the water pump gasket (2).Clean the water pump gasket mating surfaces.Installation ProcedureInstall the water pump gasket (2).Install the water pump (1). Notice: Refer to Fastener Notice in the Preface section.Install the water pump bolts. TightenTighten the bolts to 10 N·m (89 lb in).Install the water pump pulley.Install the water pump pulley bolts. TightenTighten the bolts to 25 N·m (18 lb ft).Install the drive belt. Refer to Drive Belt Replacement for the 3.4L engine.Install the drive belt shield.Install the drive belt shield bolt. TightenTighten the bolt to 10 N·m (89 lb in).Fill the cooling system. Refer to Cooling System Draining and Filling./////////////////////////////////////////////////////////////////////////////////////////////////Water Pump Replacement (3.8L)Removal ProcedureDrain the cooling system. Refer to Cooling System Draining and Filling .Loosen the water pump pulley bolts.Remove the drive belt. Refer to Drive Belt Replacement in Engine Mechanical - 3.8L.Remove the water pump pulley bolts.Remove the water pump pulley.Remove the power steering pump and reposition. refer to Power Steering Pump Replacement in Power Steering System.Remove the water pump bolts.Remove the water pump.Remove the water pump gasket.Clean and inspect the water pump mating surfaces.Installation ProcedureInstall the water pump gasket.Install the water pump.Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.Install the water pump bolts. Tighten• Tighten the long water pump bolts to 34 N·m (25 lb ft). • Tighten the short water pump bolts to 22 N·m (16 lb ft).Install the water pump pulley.Install the water pump pulley bolts. TightenTighten the bolts to 13 N·m (115 lb in).Install the power steering pump. Refer to Power Steering Pump Replacement in Power Steering System.Install the drive belt. Refer to Drive Belt Replacement in Engine Mechanical - 3.8L.Fill the cooling system. Refer to Cooling System Draining and Filling .
