answersLogoWhite

0


Best Answer

The timing marks for the cam sprocket on a 98 S10 is on the front. The marks for the crank shaft is on the oil pump gear.

User Avatar

Wiki User

โˆ™ 2014-11-19 23:12:42
This answer is:
๐Ÿฆƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: Where are the timing marks on a 98 S10 22 cam sprocket?
Write your answer...
Submit
Related questions

Where are the timing marks on a 96 S10 22 cam sprocket?

Look closly at the sprocket and you will see a small dot or indentation,you align both dots (cam and crank sprocket dots)


What does the cam sprocket line up with when putting on a timing chain?

Generally, for most single cam engines, there is a dot or mark on the cam sprocket and a similar mark on the crank sprocket. Point them at each other. the timing marks on the crank and cam sprockets must be lined up with marks on the timing chain in an overhead cam engine


Isuzu 320 V6 cam gear timing marks?

The cam gear timing marks for a Isuzu 320 V6 are located on the cam sprocket and the timing chain itself. The marks must be aligned with each other to ensure proper initial timing.


How do you set cam timing on a 4.6 SOHC?

The cam timing on a 4.6 SOHC engine is set by aligning the timing marks of the timing chain to the cam sprocket. This sets the initial timing based on factory settings.


Where are the timing marks for 2002 Ford Explorer?

The timing marks for a 2002 Ford Explorer are located on the timing chain and cam shaft sprocket. They must be aligned with each other to set the initial timing.


How does one find the timing marks for a '95 S-10 - 2 point 2 liter engine?

ON MY 2.2 4CYLINDER ( 1999 ) YOU HAVE TO PULL THE TIMING CHAIN COVER TO SEE THE " TIMING MARKS " . ON THE CRANK SPROCKET IT IS A PUNCH MARK.....ON THE CAM SPROCKET IT IS A SMALL HOLE IN THE SPROCKET . BOTH MUST LINE UP WITH TABS ON THE CHAIN TENSIONER. THE REST OF THE TIMING IS DONE BY CRANK & CAM SENSORS AND THE COMPUTER.


Where do you set the marks on the cam and the crank on a1990 2500 5.7?

assuming youre replacing the timing chain. the cam and crank sprocket marks are to point directly towards each other.


What is a cam sprocket?

A cam sprocket is a part which is attached to one end of a cam shaft in an engine. A cam sprocket, along with the timing belt maintain the timing between the camshaft and crankshaft, which ensures that the engine runs properly.


How are the timing marks lined up on a 1992 Hyundai 1.5?

The timing marks on a 1992 Hyundai 1.5 are lined up by placing the indicators on the cam sprocket and crankshaft sprocket across from each other. This sets the initial timing which determines which determines the synchronization between the engine's internals.


On a 2001 smart car where is the timing marks for the timing chain located?

On a 2001 Smart Car, the timing marks for the timing chain are located along the cam sprocket and the edge of the links. They must be matched together to ensure proper initial timing.


How should the timing marks line up on a 1969 Ford 360?

The timing marks on a 1969 Ford 360 should line up between the timing chain and the cam sprocket. This sets the initial timing which can later be adjusted using a timing light.


Where are the timing marks for a 1994 Mitsubishi Galant es?

when using a timing light, the marks are usually found on a tab/plate mounted n he engine above the crankcase damper. in timing belt instalation, the marks are place on the valve cover(s), cam sprocket(s) and crank sprocket. it depends on the engine type and the area of "timing" involved.


Where are the timing marks for a 1987 2.2L dodge Dakota?

The timing marks on a 1987 2.2L Dodge Dakota are located on the timing chain and the cam sprocket. They must be perfectly aligned to prevent the pistons and valves from hitting each other.


What are the valve timing settings for a 1990 Galant 2.0L?

If its a single cam engine the top dead center marks will be on the crank sprocket and the oil pump housing. (notches facing upward) and on the cam sprocket the notch is on the cam cover. You musnt remove it when timing the engine sprockets. . On DUAL cam 2.0 the intake and exhaust cams have 2 marks. the intake (rear sprocket) will have a notch facing up and one toward the front of the car. The exhaust cam sprocket(front one) will have a mark facing upward and the other aligning with the intake one but it will be facing rear. They must be pointing towards each other. the crank sprocket is the same as the single cam alingment.


What is the location of the timing marks on a1989 Toyota tercel?

The timing marks are on the lower timing belt sprocket on the main crank. It's a small notch you can match it with the pointer on the oil pump casing. The top mark for a 3e engine is on cam sprocket in the 12 o'clock position. It has a hole you can look through to see the notch.


How do you set timing on a 97 2.3 Leiter ford ranger?

Line crank shaft pulley timing mark on tc mark on timing belt cover. Look at cam shaft timing belt sprocket and locate the small triangle (not diamond shape) located on the plate attached to the timing sprocket. Referencing the timing sprocket look approximately at 5:00 o'clock under the timing sprocket and locate the other small triangle. Line these 2 marks up. Put timing belt on. Make sure the cam shaft sprocket and crank shaft sprocket do not turn while installing the belt. The crank shaft pulley must be removed in order to get the timing belt on.


What are the timing marks for a 93 Dodge colt with a 1.5 liter engine?

The timing marks on a 93 Dodge Colt with a 1.5 liter engine are located on the timing chain and the cam sprocket. They must line up with each other to ensure proper initial timing.


How do youst the timing chain marks on a 2002 Nissan altime whit a 2.5 engine?

2 blue marks on chain -cam sprocket marks.yellow colour mark -crankshaft sprocket.make sure crank sprocket is at 12 o clock


How to align timing marks on Nissan pick up 2.4?

Turn crank till number one cylinder is at top dead center on compression stroke. Both intake and exhaust valves will be closed. Turn cam till key way on cam sprocket is at 12 oclock position as well the crank shaft key way should also be at 12 o'clock position. Install crank shaft timing sprocket and cam sprocket with timing marks facing outward. The cam mark should be at about the 3 o'clock position and the crank mark will be about the 5 o'clock position. Look at the timing chain and find the two links that are a different color install chain so as to match these two links to timing marks on sprockets. Install guides and tensioner .


Timing marks on a single cam neon?

how to set the timing marks on a single cam dodge neon


How do you align a camshaft sensor in 89 cougar supercharged 3.8?

The sensor is a "hall effect" sensor, to align it; just match timing marks on cam sprocket to mark on crank sprocket (so they are as close as possible).


Which way do timing marks face on cams on vectra 2.ltr?

With #1 cylinder at TDC the camshaft sprocket marks are adjacent to each other. If you stand at the right wing looking at the marks,then the rear cam mark is at 3 o'clock and the front cam mark is at 9 o'clock.


Which timing mark do you use to set timing belt on a 1998 metro cam sprocket has two marks. engine is 1.3 liter?

On my 2000 Metro with a 1.3L the mark and slot marked with the "E" are used.


Where is the timing marks on a 2.2 motor?

the timing marks are on the cam and crank gears in the timing case.


Where are timing marks for 2.0engineon a ford escort?

I am not familiar with this engine in particular but most engines have the timing marks stamped into the block with a corresponding dot or arrow on the crankshaft damper which tells you where top dead center (TDC) is. After aligning these timing marks you would look at the camshaft sprocket(s). If it is a single overhead cam (SOHC) there will be markings similar to those for the crankshaft, one on the cylinder head and another on the camshaft sprocket. Or, if it is a dual overhead cam (DOHC) there is typically one arrow on each of the camshaft sprockets that you align to be pointing at one another.