0
What else can I help you with?
How do you re-spool window cable?
To re-spool window cable, first, remove the window mechanism from the frame. Carefully unwind the old cable and clean any debris from the spool. Then, attach the new cable to the spool, ensuring it's secured properly. Finally, wind the cable evenly around the spool, making sure it doesn't tangle, and reassemble the window mechanism.
How do you fix a jammed weed wacker?
Stop motor. Remove line spool. pull spool from shaft and remove cord or weeds from around shaft. Replace spool on shaft. Re start motor.
How do you change the trimmer line on a Ryobi Expand-It?
To change the trimmer line on a Ryobi Expand-It, first remove the spool cover, then take out the spool and replace the trimmer line following the arrows on the spool. Finally, reassemble the spool cover.
How do you change the spool on a craftsman bushwacker weed eater?
I can't seem to get the spool off.
Where do the cable end on the electric window motor connect to?
The ends connect to the spool that's driven by the motor.Once that come off the track or break, you cannot repair them. You must replace the entire regulator.Here's how:http://www.ricksfreeautorepairadvice.com/repair-topics/window-power-repair/replace-a-power-window-regulator
How do you change spool on RTE 115?
To change the spool on an RTE 115 trimmer, first, ensure the trimmer is turned off and unplugged for safety. Remove the old spool by pressing the release tabs on the spool cover and lifting it off. Then, insert a new spool by aligning it with the spool holder and ensuring the line feeds through the eyelets. Finally, replace the spool cover securely, and the trimmer is ready for use.
How do you replace a Sport trac rear window motor?
How to replace the rear window motor on a 2001 Sport Trac: 1. fold down the rear seats. 2. flip up and remove the spring-loaded hinge on the cargo platform by removing the philips-headed screws. 3. remove the plastic fasteners for the rear plastic body panel. 4. pry the plastic rear body panel from the tabs at the top (left and right). 5. remove the two plastic felt fasteners. 6. peel down the motor cover located behind the rear right seat. 7. remove the 3 torx bolts on the motor. 8. using a large screwdriver or small pry bar, pry the motor away from the cable spool, leaving the spool intact on its mount. 9. unplug the motor and remove. 10. using a screwdriver, rotate the spool to give it some play (the window should move some). 11. put a dab of grease on the motor hub. 12. install the new motor by aligning the hub splines and rotating the motor into position. tighten the torx bolts. 13. Reassemble everything. 14. Initialize the new motor: open door, turn key to 'on', push rear window button 6 times, turn key to 'off', push rear window button 6 times, turn button right until window closes all the way, turn button left until window opens all the way.
How to change the line on a Ryobi weed eater?
To change the line on a Ryobi weed eater, first, remove the spool cover and take out the old line. Cut a new line to the correct length and insert it into the spool. Wind the line evenly and securely onto the spool, then reassemble the spool cover.
Do a electric weed eater have littke bb's in it?
No, electric weedeaters have a motor and a cord spool.
The driver side window in a 1994 GrandAm will not roll up when you press the switch what could be wrong with it How much will it cost to fix it?
The window works on sort of a pulley system. 2 cables pull at the bottom of the window to go up or down. The cables become frayed and no longer can go into the protective sheath or the spool. You will need to take off your door skin, unbolt your motor and spool. Then unhook the cables at any point they are attached and replace them. As for the cost, dont know. I cut my cables and put my window up and down with my hand. I use my car for work so im not worried about it. Hope this helps out.
How do you change the spool on a Ryobi trimmer?
To change the spool on a Ryobi trimmer, first, remove the trimmer head by pressing the tabs on the side. Then, remove the old spool and replace it with a new one, making sure it is securely in place. Finally, reattach the trimmer head and you're ready to trim.
What could cause a Weedeater trimmer spool to not spin if the motor runs and revs up nicely?
Take the spool off the the machine. By that I mean the part that contains the cutting line. There will be a spring that drives the spool. Get a pair of pliers and gently pull on it. If it comes out of the shaft it is probably broken or it came loose. If that does not solve the problem look at the spool where the nut is located make sure its there and that the housing is not wallowed out. If so buy a new spool.
