answersLogoWhite

0


Best Answer

you have to take the wheel off first of all.Then you will see,bolted on to the axle,right over top the brake rotor is the brake caliper,fastened by two bolts that you remove,causing the whole caliper to come loose.next u will see two more bolts of close to the same size holding the brake slider in place.remove them.now u can remove the pads from the slider.before putting the new pads in the slider, take two c-clamps and push both plungers back as far as they go.now,put the new pads in place,bolt the slider onto the caliper,bolt the caliper to the axle mount,and put the wheel back on. Good Luck!! you have to take the wheel off first of all.Then you will see,bolted on to the axle,right over top the brake rotor is the brake caliper,fastened by two bolts that you remove,causing the whole caliper to come loose.next u will see two more bolts of close to the same size holding the brake slider in place.remove them.now u can remove the pads from the slider.before putting the new pads in the slider, take two c-clamps and push both plungers back as far as they go.now,put the new pads in place,bolt the slider onto the caliper,bolt the caliper to the axle mount,and put the wheel back on. Good Luck!!

User Avatar

Wiki User

โˆ™ 2009-01-14 03:48:58
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: How do you change your brake pads on your Chevy S10?
Write your answer...
Submit
Related questions

How to change Front Brake Pads on 97 Chevy S10 Truck?

you pull off the front wheel, then you remove the break caliper, then replace the break pads,.., it helps if you have a large C-clamp..


What would cause a sort of rubbing noise like low brake pads on the rearend of a 1998 Chevy S10 after replacing both bearings?

Low brake pads, misassembled brake parts?


How do you adjust the emergency brake on your 2001 S10 Chevy?

How do you adjust the emergency brake on your 2001 S10 Chevy?


What size wrench do you need to change the brake pads on a 1994 s10?

3/8" allen wrench.


How do you find a brake switch wiring diagram for a 1997 Chevy S10?

where can i find a diagram for a 1997 chevy s10 brake switch?


How to check front brake pads on Chevy s10 truck 1997 model?

Look at the pads and measure the thickness. The minimum allowed thickness for the brakes pads is 2 mm. Replace if they are worn to this point. You will have to remove the wheel to measure the pads.


What size allen wrench is required to change front brake pads on 2000 Chevrolet s10 truck?

3/8"


Chevy s10 hydraulic brake system diagram?

where is the drake light switch on a 1999 chevy s10. The brake light switch is located just above the brake pedal. You will need a flashlight to see it.


How do you change the front shocks on 2000 Chevy S10 pickup?

how to change front shocks in 01 Chevy s10


How do you release a stuck parking brake on 1999 S10?

my parking brake release did not take off the parking brake on my 2001 chevy s10? is there a way to disengage it?


How do you change the third brake light on Chevy s10?

You didn't mention what year the S10 is but, you can probably remove the 2 small screws that hold the lens to the housing and you will have access to the bulbs.


I have a 1997 Chevy S10 pickup Lately there has been an annoying squeaking while I'm driving When I apply pressure to the brake the squeaking stops When I remove pressure from the brake it returns?

Very likely the brake pad warning strip. It's a device deliberately set into the brake pads of many GM vehicles that gives you an audible notification that the brake pads are almost worn out.


Why brake light stays on 1993 Chevy s10?

Defective or misadjusted, brake light switch.


How do you change a master cylinder for a 1998 Chevy S10?

How do you change a Master Cylinder and hydraulic clutch line for a 1998 Chevy S10?


What type of brake fluid does a Chevy S10 use?

DOT 3


What do you do if you have no emergency brake after replacing the rear pads and drums of a 2001 Chevy S10 4WD?

There are a number of things that you can have done wrong. Get a manual on your car from the parts store and it will tell you how it is supposed to work.


Brake light on 1986 Chevy s10?

The brake light switch located above the brake pedal is broken or out of adjustment.


How do you change brake calipiers on a 1996 Chevy s10?

Remove wheel, remove the bolt holding brake hose to the caliper, remove the two pins that hold the caliper to the caliper bracket using a 3/8" allen wrench, remove caliper. Inspect brake pads and brake hose for damage, replace if necessary. Install new brake caliper in reverse order. Bleed system.


Where is the brake fluid dipstick located at in a 1993 Chevy s10 truck?

The brake fluid reservoir does not have a dipstick.


How do you change front brake pads?

how do you change the brake pads on a 2003 S10 BLAZER To change the front pads you need to jack up blazer and pull off wheel.the brake caliper is held on by two hex head bolts.Remove these and gently pry the caliper up off the rotor.You will need a C- clamp to compress the piston back into the caliper ,so when you install the new pads ,the caliper will fit back over the rotor. put the two hex bolts back in ,and your done.


How to change rear oil seal on Chevy S10 PU 4cly 2.5 engine?

Chevy S10 pickup 4cly 2.5 engine,how to change rear oilseal


Why won't brake lights turn off on my 1998 Chevy s10?

Probably a misadjusted or defective brake light switch.


What is the difference between an S10 and a Chevy S10?

An S10 is the same as a Chevy S10.


How do you change the front brake rotors on a 1988 Chevy S-10 pickup?

Need to know if this is a 2 wheel or 4 wheel drive S10.


Chevy 1992 s10 pu no brake lights?

Check the bulbs, Check the fuse, Check the brake light switch, in that order.