0
If the MT2 voltage exceeds VDRM such as might occur during severe and abnormal mains transient conditions, MT2-MT1 leakage will reach a point where the triac will spontaneously break over into conduction.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How rms voltage related to peak voltage?
The average voltage is the rms voltage.Volts peak = volts RMS times 1.414Volts RMS = volts peak times 0.7071Use the link below to an RMS voltage, peak voltage and peak-to-peak voltage calculator.********************************The average voltage is not the r.m.s. voltage.The average voltage of a sine wave is 0.636 x the peak value. Conversely, peak voltage is 1.57 the mean or average.
What is difference between amplitude and peak value?
It is the highest value of the amplitude, called the peak value. Scroll down to related links and look at "RMS voltage, peak voltage and peak-to-peak voltage". Look at the figure in the middle below the headline "RMS voltage, peak voltage and peak-to-peak voltage".
Are peak-to-peak and rms voltage measurements the same?
No, the peak-to-peak voltage is 2sqrt(2) times as much as the rms for a pure sine-wave.
What is the minimum required peak voltage rating for a diode with voltage source is 100V peak?
200 V
How to calculate the peak-to-peak value of a signal?
A: AC or our line voltage is sinusoidal in nature it goes up to a positive peak returns to zero and proceed to the negative peak. 120V AC is actually swinging from peak to peak. It is 120 volts but the peak is the 120 v times 1.41 or 169.2 volts and since it also go negative then the peak to peak 120 volts times 2.82 or 338.40 volts or twice the peak voltage
What is peak to peak voltage?
Conversions of RMS voltage, peak voltage and peak-to-peak voltage. That are the used voltages. The expression "average" voltage is used for RMS voltage.Scroll down to related links and seach for "RMS voltage, peak voltage and peak-to-peak voltage".Answer'Average' is not the same as 'root mean square'. As the average value of a sinusoidal voltage is zero, you cannot convert it to a peak-to-peak value.
How do you measure peak voltage using oscilloscope?
You measure the peak to peak voltage and divide by 2.
How do you convert peak voltage to peak-peak voltage?
Simply multiply the peak voltage to 2 and you will get the peak to peak voltage.
What is the peak-to-peak voltage in a circuit with an rms voltage of 120VAC?
ANSWER: The peak to peak voltage can be found by multiplying 120 v AC x 2.82= 339.41
What is the difference between 1n4004 diode and 1n4007 diode?
The main difference between a 1n4004 and a 1n4007 are in the maximum RMS voltage, the maximum DC blocking voltage and the maximum repetitive peak reverse voltage. These are 280 and 700, 400 and 1000, and 400 and 1000 volts respectively.
What is a peak load voltage out of a bridge rectifier for a secondary voltage of 15 Vrms?
A: Peak voltage is RMS multiplied by a factor of 1.41
What is average voltage?
Another name for average voltage is the RMS (Root Mean Square). This is a voltage derived from the peak to peak voltage multiplied by .707. If the peak to peak voltage is 170 volts then the average voltage (RMS) would be 170 x .707 = 120 volts.
How rms voltage related to peak voltage?
The average voltage is the rms voltage.Volts peak = volts RMS times 1.414Volts RMS = volts peak times 0.7071Use the link below to an RMS voltage, peak voltage and peak-to-peak voltage calculator.********************************The average voltage is not the r.m.s. voltage.The average voltage of a sine wave is 0.636 x the peak value. Conversely, peak voltage is 1.57 the mean or average.
What is difference between amplitude and peak value?
It is the highest value of the amplitude, called the peak value. Scroll down to related links and look at "RMS voltage, peak voltage and peak-to-peak voltage". Look at the figure in the middle below the headline "RMS voltage, peak voltage and peak-to-peak voltage".
What is the effective voltage for a peak voltage of 311 volts?
When the peak voltage is 311, the RMS voltage is 220. (311 * square root (2))
Are peak-to-peak and rms voltage measurements the same?
No, the peak-to-peak voltage is 2sqrt(2) times as much as the rms for a pure sine-wave.
Why is the peak voltage not exactly equal to the peak voltage of the alernating voltage and by how much it differ?
If you are referring to the voltage after the rectifiers in a powersupply, it is due to the voltage drop across the rectifiers.
