answersLogoWhite

0

remove the pass. finder linner and find plug to the motor and disconnect it

User Avatar

Wiki User

14y ago

What else can I help you with?

Related Questions

How do you turn power off to your antenna on a 91 firebird?

Disconnect wires at antenna


How to replace a 2001 Toyota Sequoia radio antenna motor?

To replace the radio antenna motor on a 2001 Toyota Sequoia, first, disconnect the battery to ensure safety. Remove the interior trim panel surrounding the antenna, typically located on the rear fender or roof. Unbolt the old antenna motor from its housing, disconnect the wiring harness, and install the new motor by reversing the steps. Finally, reattach the trim panel and reconnect the battery to complete the installation.


How do you disconnect a power antenna on a 1989 firebird?

To disconnect the power antenna on a 1989 Firebird, first, ensure the vehicle is turned off and the key is removed. Locate the antenna, which is usually found near the rear fender or trunk area, and disconnect the electrical connector that powers the antenna. You may also need to remove any screws or bolts securing the antenna to the vehicle to fully detach it. Finally, if applicable, disconnect the antenna cable from the radio before completely removing the unit.


How do you disconnect antenna power on a 1990 cutlass ciera?

To disconnect the antenna power on a 1990 Cutlass Ciera, first, locate the antenna assembly, which is usually found at the rear of the vehicle. Remove any trim panels if necessary to access the wiring. Then, disconnect the power wire from the antenna motor, typically a small connector or plug, ensuring the ignition is off before handling. Finally, if you need to remove the antenna, unscrew it from its base and pull it out gently.


How do you disconnect power antenna motor on 1988 Cadillac Fleetwod fwd?

gfdgfdg


How do you disconnect power wire to antenna?

To disconnect the power wire to an antenna, first ensure that the power source is turned off to prevent any electrical hazards. Locate the power wire connected to the antenna and identify the connection points. Carefully disconnect the wire by either unscrewing it from the terminal or unplugging it, depending on the type of connection. Finally, secure the disconnected wire to prevent accidental contact with live components.


How do I access the antenna input on 2005 Sequoia radio?

To access the antenna input on a 2005 Toyota Sequoia radio, you will need to remove the radio from the dashboard. Start by carefully prying off the trim panel surrounding the radio using a trim removal tool. Once the panel is removed, unscrew the mounting screws securing the radio, slide it out, and you’ll find the antenna input at the back of the unit. Disconnect the antenna cable if needed for your purpose.


How can you make your antenna stop going up and down in your 1993 accord?

Try finding the power cord that goes into the antenna and disconnect it


Is there a fuse or wire you can disconnect to stop the power antenna that will not stop running on an 1986 Buick LeSabre?

the antenna its self will have a connector you can unhook


How do you remove the antenna motor on a 2004 Toyota Sequoia?

To remove the antenna motor on a 2004 Toyota Sequoia, first, ensure the vehicle's battery is disconnected to avoid electrical issues. Then, access the antenna motor by removing the interior trim panel in the rear quarter panel where the motor is located. Disconnect the wiring harness and unscrew the mounting bolts holding the antenna motor in place, and finally, pull out the motor gently to detach it from the vehicle. Reassemble by reversing these steps.


How do you replace the antenna on a 1989 Toyota Camry LE Is it a power antenna?

To replace the antenna on a 1989 Toyota Camry LE, first, ensure the car is turned off and disconnect the battery. If it has a power antenna, you may need to remove the interior trim panel to access the antenna's motor and wiring. Unscrew the old antenna from the exterior, disconnect its wiring, then install the new antenna by reversing the steps. Finally, reconnect the battery and test the antenna to ensure it functions properly.


How do you stop a power antenna from running on a 1986 Cadillac Fleetwood braugham?

To stop the power antenna from running on a 1986 Cadillac Fleetwood Brougham, you can disconnect the antenna's power wire. This is typically found in the wiring harness that leads to the antenna motor. Alternatively, you can remove the fuse related to the power antenna from the fuse box to prevent it from receiving power. If the antenna is stuck, ensure that the motor or gear mechanism isn't jammed or damaged.