0
There is no way to dissolve it. It must be physically scraped off.
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
Why are your porcelain floor tiles wobbly?
This sounds as though there is not enough thinset under the tile. Or your thinset didn't properly bond to the tile. There is no real way to fix this besides pulling the tile up. If they haven't already, the tile will likely start cracking.
Can muriatic clean thinset from ceramic tile?
will muriatic acid aid in removing thin set from the back of ceramic tiles with out damage
What is the difference between thinset and mastic?
Mastic come pre mixed which thinset come in a bag that you have to mix with a mixer mastic is not good for your wet areas meaning showers or on the floor. Used mainly for back splashesr thinset is port base like cemet very strong used in wet areas outside for all types of tile installation
Can you glue ceramic tile with vinyl glue?
Not directly as the ceramic tiles will soon show through the vinyl flooring. If the ceramics are laid on a wooden floor, you must take up the tiles and overboard with 6mm plywood. If the tiles are on a concrete floor, you can leave them down and lay a latex screed on top to provide you with a smooth floor for your vinyl
Getting ready to install ceramic floor tile some videos indicate that you should lift an installed tile to check for thinset coverage other do not how do I know if I'm using the right amount?
The videos which suggest lifting a tile to check the thinset coverage on the back are right. If you are installing tile for the first time, this is a necessary step to be sure you have the technique right. For floor tile up to about 12" x 12", you'll use a 1/4" x 1/4" square-notched trowel. For larger tiles, you should use a bigger trowel - about 3/8" or so. Dip some thinset from the bucket, drop it on the floor, and then spread it out. Hold your trowel nearly vertical at the edge, with just a slight angle so you can drag out the thinset. It should leave deep grooves in the thinset that stand up on their own, and you should be able to see the floor surface between the grooves. When you place the tile, hold it as level as you can and then carefully place it on top of the thinset. Wiggle it back and forth slightly, as you apply LIGHT pressure downwards, and evenly. You want the thinset to make good contact on the back of your tile, but not so much that you flatten it out. If thinset is oozing up between tiles, you're pressing too hard. Check to see that there is no "lippage" - or uneven heights between adjoining tiles. The surface should be perfectly level to surrounding tiles. Peel up a tile, and check the thinset coverage on the back. It should cover at least 75% of the back of the tile. If it is less, then you're either not pressing hard enough, not using enough thinset or spreading it too thin, or your floor surface is too uneven. If all looks good, scrape the thinset off the tile and that section of floor where it was removed, and reapply and reinstall.
What kind of thinset for ceramic tile underwater?
Any thinset will workb
What kind of adhesive do you use on a pool liner?
Use "pool repair mortar" if it is under water or any exterior latex fortified thinset mortar if it's not under water. After trying several types of products that didn't work I used "liquid nail" which can be purchased at a local hardware store. You then have to re-grout the tile and seal them.
What are the differences in thinset grades?
The first difference is in the color - it comes in gray (use with darker tiles) or white (use with light tiles). There are three common categories with a range of products that differ in grade, curing time, composition, and price. Each type is geared to a specific environment and substrate where the tile is to be set.
How thick is the layer of thick-set mortar used with ceramic tile?
It depends on the size of the tile. Use a smaller 5/32" V-Notch Trowel for 3/4" or smaller glass mosaics, a 1/4" x 1/4" trowel for 2" x 2" mosaic tiles. For bigger 12" x 12" or heavier tiles use a trowel with bigger notches like 1/2" x 1/2" so the bond mortar (thinset) will be thicker. The 2011 Tile Industry Standards define the minimum bond layer thickness to be 3/32" after beat in, but the maximum thickness has more to do with the manufacturer of the thinset mortar you are using. Many "thinsets" max out at 1/4" in a single layer. "Medium Bed" types of thinset may go up to 1/2" or more, but you must follow the manufacturer's instructions. Thinset mortars made thicker than they were designed for can shrink and crack the tiles.
How thick is the layer of thin-set mortar used with ceramic tile?
It depends on the size of the tile. Use a smaller 5/32" V-Notch Trowel for 3/4" or smaller glass mosaics, a 1/4" x 1/4" trowel for 2" x 2" mosaic tiles. For bigger 12" x 12" or heavier tiles use a trowel with bigger notches like 1/2" x 1/2" so the bond mortar (thinset) will be thicker. The 2011 Tile Industry Standards define the minimum bond layer thickness to be 3/32" after beat in, but the maximum thickness has more to do with the manufacturer of the thinset mortar you are using. Many "thinsets" max out at 1/4" in a single layer. "Medium Bed" types of thinset may go up to 1/2" or more, but you must follow the manufacturer's instructions. Thinset mortars made thicker than they were designed for can shrink and crack the tiles.
How might one apply ceramic wall tiles?
One might apply ceramic wall tiles by using either of 2 products: tile mastic or thinset mortar. The application process is the same for both products. One could use a V-notched trowel to spread some of the mortar onto the wall, covering an area just big enough to lay in about 8 tiles.
How do drink manufactures get enough carbon dioxide to dissolve and make fizzy drinks?
it disolve in under pressure
