Chevy Silverado
Chevy S-10
Ford Windstar GL

How do you figure out what 350 small block engine will directly mount up to your factory 99 s10 motor mounts?

151617

Top Answer
User Avatar
Wiki User
2011-09-13 01:33:27
2011-09-13 01:33:27

a converson kit is available that contains all you need to make the converson with instructions the kit is less expensive then buying parts seperately

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Carquest is where i got mine... get motor mounts factory spec this will keep other parts of your engine from having to absorb the shock of the motor

User Avatar

The 1995 Dodge Neon engine mounts are located on each corner of the engine. There will be to engine mounts in the front and two engine mounts in the rear.

User Avatar

it has 4 mounts , 2 engine mounts, and 2 transmission mount

User Avatar

It should be fairly straightforward if you put a set of v8 mounts on the engine and drop it in to the engine bay. Hook it up to the transmission, level the rocker covers, and mark the holes for the mounts. Then you can take the engine back out, install the mounts, and reinstall the engine. That year was available with a v8, so you should be able to use factory accessory brackets.

User Avatar

how many engine mounts are there on a 1991 corolla.

User Avatar

There are four motor mounts. One directly in front of the engine is mounted to the carriage and has black rubber dampening, One directly behind the engine also mounted to the carriage and with rubber dampening. One on the passenger side directly above the axle mounted to the body and one on the drivers side attached to the body and transmission.

User Avatar

There are 2 motor mounts- one on each side of the engine. The trans/transfer case then also have a mounting on the big skid plate. If you look on each side of the engine toward the bottom, you should see the motor mounts. The driver's side is harder to see due to the intake/exhaust manifolds. There should be rubber mounts that the engine sits on.

User Avatar

Chevrolet engine mounts are two-piece designs, whereby one piece attaches to the engine and the other to the frame. Motor mounts are fairly durable, but old mounts can break when subject to heavy acceleration. Fortunately, the engine does not have to be removed to remove the mounts.

User Avatar

how do you remouve engine mounts on 1995 Hyundai sonata

User Avatar

Motor/engine mounts. Number of mounts and configuration differs from one vehicle to the next.

User Avatar

Engine mounts on a car are very difficult to repair and can cost thousands of dollars as the engine must be removed.

User Avatar

From the battery to frame directly under the battery box. From the frame to the engine at the motor mounts with a short ground cable. Usually on the drivers side.

User Avatar

You need to support the engine when removing any mounts. The mounts bolt to the engine, and bolt to the unibody of the car. You can find the locations of all of the engine mounts by hunting around the engine bay or by picking up a Chiltons and Haynes manual.

User Avatar

The 1999 Mitsubishi has four motor mounts. There is a motor mount on each corner of the engine. The motor mounts can be seen from the bottom of the engine.

User Avatar

An Audi tt is known to have 7 engine motor mounts. It is suggested that that stretch bolts be used when replacing the mounts to ensure the right amount of torque is applied to hold the engine in place.

User Avatar

No. The tranny mounts are a different pattern.

User Avatar

no its a1997 avalon replacing the mounts

User Avatar

Worn rubber on motor mounts. Replace mounts.

User Avatar

The cost to replace engine mounts on this car can run between $30-$300+. This can cost even more depending on where the mounts are bought, the brand of the mounts, and if someone else does the work.

User Avatar

If the old mounts were compressed over the years, there could be a small lift of the engine with new mounts. If the lift is more than an inch or so, you should check that the proper mounts were installed.

User Avatar

Lift and properly support front of car. Remove the nuts from lower half of the mounts (one per mount). Raise engine enough for the mounts to clear the frame brackets and support engine safely. Unbolt motor mount brackets from engine block. Remove mounts with engine bracket. Unbolt motor mounts from engine brackets on the bench. Reverse procedure for installation.

User Avatar

The 1997 Buick is equipped with four motor mounts. There will be to motor mounts on the rear of the engine and two motor mount on the front of the engine.

User Avatar

You can put a BMW 525 engine into a BMW 325. The motor mounts will need to be changed. The 525 engine motor mounts will not match the 325 engine compartment.

User Avatar

It depends on the exact model to which you are referring. Earlier models had three engine mounts; later models used four. If you are not comfortable or familiar with changing engine mounts, your best bet is to see an authorized mechanic, who can do the work needed.

User Avatar

You'll need to move the frame mounted engine mounts. There should still be holes drilled in the frame for the V8 version. I don't remember which holes to use....it's been a few years since I did the V6 to V8 conversion on these cars. Get the motor mounts for a 78 or up Malibu with a 305 or 350. You may have to mount these to the engine and lower it into the frame to figure out where to mount the frame mounts.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.