answersLogoWhite

0


Best Answer

DON'T KNOW WHAT A RD-628 IS BUT: A CHEMICAL PUMP WITH A SOLUTION CONTAINING PROPER MIX OF GLYCOL (IF NECC.) AND CORROSION INHIBITERS. TEST WATER FIRST THEN ADD PROPER SOLUTION. IF IT IS A CONVENTIONAL SYSTEM WITH A BACKFLOW PREVENTER, PRESSURE REDUCING VALVE, ETC. IT SHOULD FILL BY ITSELF IF ALL PARTS ARE WORKING PROPERLY. PRV FROM THE FACTORY ARE PRESET AT 12#. IN A PINCH, W/O TAKING THE QUALITY OF THE SOLUTION INTO ACCOUNT, AND IF NO MANUAL BYPASS IS PROVIDED, YOU CAN TAKE A WASING MACHINE HOSE FROM A BOILER DRAIN VALVE ON ONE SIDE AND RUN IT TO A VALVE WITH POTABLE WATER ON THE OTHER SIDE, OPEN POTABLE VALVE FIRST, PURGE AIR FROM HOSE AND FILL BOILER TO A NOMINAL PRESSURE OF 12#. YOU WILL NEED MORE PRESSURE IF IT IS A MULTI LEVEL STRUCTURE. NOTE: THE PURPOSE OF THE BACKFLOW PREVENTER IS TO KEEP THE BOILER H2O FROM BEING INTRODUCED INTO THE POTABLE SUPPLY, SO BE CAREFULL, IT TASTES BAD AND MAY NOT BE GOOD FOR YOU DEPENDING WHAT IS IN THE BOILER NOW. LC

User Avatar

Wiki User

15y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you fill up a RD 628 boiler?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

What is the start up procedure of AFBC Boiler?

what is light up procedure of afbc boiler


What is economiser in boiler?

In boilers, economizers are heat exchange devices that heat fluids, usually water, up to but not normally beyond the boiling point of that fluid. Economizers are so named because they can make use of the enthalpy in fluid streams that are hot, but not hot enough to be used in a boiler, thereby recovering more useful enthalpy and improving the boiler's efficiency. They are a device fitted to a boiler which saves energy by using the exhaust gases from the boiler to preheat the cold water used to fill it (the feed water).


What is caking in a boiler?

Caking is the build up of limescale.


What are the most common boiler problems?

The most common boiler problems often arise because the boiler is not maintained. One is that in hard water areas the element is furred up and so it is not able to heat up the water as it should. Another is that the insulation is shifted and so no longer covers the boiler and keeps the heat in.


What is meant by the super boiler?

A Super Boiler is an energy saving boiler with advanced controls. Super boilers reduce the cost of fuel as well as carbon based emissions up to 40%.


What is the purpose of an industrial boiler?

An industrial boiler heats up the whole building and provides a lot more heat than a standard boiler it is designed to be used in places like power stations.


What is the use of economiser in boiler?

The economizer is used to raise feedwater temperature up to nearly the temperature of the boiler to avoid thermal shock and improve the boiler's efficiency. Every 11 degrees Fahrenheit increase in feedwater temperature yields a 1% increase in boiler efficiency.


How much would it cost to get a boiler?

A new boiler will cost about $3000 for a standard efficiency model, but for a more efficient boiler it can run up to $8000 plus. It is important to have a contractor size up your system. If you buy a more efficient system the boiler will not need to be the same size as your old boiler unit. Keep in mind that you location and seasonal demand will affect the price as well. If a contractor is super busy they will likely charge more since they have plenty of jobs lined up in the future.


Why economiser is used in boiler?

An economizer is used to heat boiler feedwater up closer to the temperature of the boiler water, using heat from the boiler exhaust gases, heat that would otherwise be wasted. The main reason is to improve the efficiency of the boiler. For every 44 degree F drop in exhaust gas temp. there is an 11 F rise in feedwater temperature and a 1% gain in boiler efficiency.


What welding rod do you use for welding boiler plate?

Totally depends on what the boiler plate is made up of. Normally this data is supplied to the welder operator.


What is the feed check valve of boiler?

The feed check valve of a boiler is on the line coming out of the boiler it is usually to prevent the water from going back in to the boiler its coming out of so it would build up excessive amounts of pressure which will cause the t&p valve to blow temperature and pressure


Boiler Installed?

form_title=Have a Boiler Installed form_header=Set up a new heating system in your home by using steam generated by a boiler. What is the square footage of the space to be heated?=_ What kind of HVAC system is currently installed?=_ Is this boiler for a residence or commercial facility?= () Residence () Commerical () Other