2000-2005 Dodge & Plymouth Neons
Pontiac Sunfire
Grand Am GT

How do you gain access to replace the bulbs over the license plate on a 2002 Pontiac Sunfire?

262728

Top Answer
User Avatar
Wiki User
2015-07-15 20:09:25
2015-07-15 20:09:25

you can see the plugs on the back of the light.

lift the trunk and look past the license plate . the twist out . righty tighty lefty lousy . pull them out. its tight but they come out. use needle nose pliars, but be gentle.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

You need to remove the liner on the trunk lid. That will give you access to the license plate lights housing. Remove the sockets by twisting 1/4 turn and replace bulbs. Size for bulbs are 2825

User Avatar

I'm guessing that you're referring to the lamps that light up the PONTIAC name across the center of the trunk lid. You access those lamps from the inside of the trunk lid IE: the back of the PONTIAC name. Mine were pretty stuck in place, so I ended up removing that entire rear light assembly. It comes out with about 6 screws. That gives you more access to the connectors.

User Avatar

I can't tell you precisely, but you'll see it when you pull the inside door panel off to access it.

User Avatar

Not positive on your model, but open the driver's side door and look at the end of the dashboard. There should be a little access panel.

User Avatar

It looks as if I'll have to crawl under the front of the car to access the bulb to replace it.

User Avatar

Open the hatchback and locate the trim plate inside the hatchback. Pry it off with a thin plastic tool such as a putty knife to gain access to the lamps.

User Avatar

you have to take all brakes and rotor off the hub. then you must spin the hub so the access hole is in front of the bolts,and take all 3 bolts off. then you must pull the hub off of the spline.

User Avatar

It's on the passenger side of the engine at the rear. You need to access it from underneath the vehicle. (unless you have really small hands!!)

User Avatar

If there is not an access hole in the rear trunk type area you will havfe to remove fuel tank to access

User Avatar

Those bulbs are very common. You should be able to find them at Auto Zone/Checker etc. There are a few of them behind that PONTIAC name. You access them from inside the trunk lid.

User Avatar

It's located on the engine side of the radiator. Lower passenger side. You have to get under the car to access it though. You can't see it from the top.

User Avatar

One in each door have to remove door panels for access & 2 0n deck lid in trunk get acces to trunk for these speskers.

User Avatar

It is located in the front of the engine, above the oil filter, next to the starter. Your going to have to remove the starter for easier access to the sensor.

User Avatar

Drain the fuel tank and then remove it from the vehicle. This will give you access to the fuel pump.

User Avatar

Ive been trying to figure this out myself,there's no bulb on mine.An no apparent access to it from outside or the trunk

User Avatar

It's located inside the fuel tank. You will have to drop the tank to gain access to the pump. I suggest picking up a Haynes or Chilton manual for the car and following their instructions.

User Avatar

You can access the backup light on your Pontiac from the trunk compartment. Remove the backup light cover. Take hold of the backup light connector, push in and turn at the same time. Do the same with the backup lightbulb. Reverse the process to install the new lightbulb.

User Avatar

Unscrew the bulb from the back of the light assy. If you have to you may need to remove it from the vehicle. Remove head light assembly(2 screws) Easy access to bulb/socket.

User Avatar

The fuel tank has to be removed, as access is through the top of it. This is a pretty big job and there are safety considerations. I suggest picking up a Haynes or Chilton manual and following their procedure.

User Avatar

in a 99 there is easy access in the trunk, if u pull out the interior you will see it toward the back seats.

User Avatar

You don't state what year your Sunfire is, so I don't know if there are any shrouds or other things blocking access, but this should be a fairly direct job. Check out this tutorial: http://www.ehow.com/how_112575_change-cars-battery.html Bear in mind, that if you don't know the security code to your radio, you risk rendering it useless when you disconnect the battery.

User Avatar

factory recommendation is to cut a hole in the inner fender well to access/replace it.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.