answersLogoWhite

0


Best Answer
Copy

One bolt on the front (right) engine mount needs to come out. There is a sleeve around this bolt that will come out after the bolt is gone, allowing you to take the belt out and replace it with a new one. Just check out the front engine mount and you will see which bolt has a sleeve around it to remove (lower front bolt if I remember correctly).

Make sure to memorize/write down how the belt follows the pulleys -before- removing the belt. You don't have to do this, but it sure makes putting the new belt in much easier as you don't have to learn how the belt makes its rounds.

Owner of a 1995 Bonneville SE 172k miles (second engine at 149k, swapped out in my garage)

User Avatar

Wiki User

โˆ™ 2015-07-15 21:33:06
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you install the serpentine belt on a 1995 Pontiac Bonneville without a super charger?
Write your answer...
Submit

Related Questions

Install a transmission mount on 1989 Pontiac Bonneville?

i would rather not...


How do you install air door actuator in 2000 Pontiac Bonneville Where is this part located?

replace temperature door actuator.


How do you install the armrest on a 1993 Pontiac Bonneville?

I have a 1996 Bonneville and it has a Phillips head screw on each side of the armrest. If yours is like that then you should be able to just unscrew them and pop it out.


How to install heater core on 1996 Pontiac Bonneville?

You don`t want to go there !( Trust me.) Take it to a radiator shop.


How do you install a thermostat in a 1995 Pontiac Bonneville?

i just farted,how can i stop farting cause it smells like egg salad sometimes


How do you install a transmission in a 2000 Pontiac bonneville?

For such a large job, if it is not obvious to you, you should be using a repair manual, or take it to a competent shop.


How do you replace a headlight on a 1997 Bonneville?

Begin by removing the wiring harness from the back of your 1997 Pontiac Bonneville headlight. Remove the headlight assembly retaining bolts. Reverse the process to install your new headlight.


Replace ignitio switch in a 1990 Pontiac Bonneville?

Begin by removing the retaining ring at the top of your 1990 Pontiac Bonneville ignition switch. The ignition switch will slide out. Remove the wiring harness from the end of the ignition switch. Reverse the process to install your new ignition switch.


Replacing heater core on 1997 Pontiac Bonneville?

Begin by training the water from your 1997 Pontiac Bonneville cooling system. Remove the heater core water supply hoses. Remove the heater core retaining bolts. Reverse the process to install the new heater core.


How do you install a serpentine belt on a 1996 Corsica?

how do you install a serpentine belt on a 1996 corsica?


How do you Install F250 serpentine belt?

how to install a serpentine belt on 1989 f250 diesel 7.3l


You need a diagram of how to install a serpentine belt on a 1998 Bonneville?

diagram of ur belt should be right under ur hood..should be a sticker there showning how the belt should fit


How do I install a water pump on a 1998 Pontiac Bonneville?

You have to remove the motor mount. Once the motor mount is removed you can remove the old water pump and install the new one. Make sure the area is clean before you install the new one.


How do you install 1998 Pontiac Bonneville taillights?

On the other side of the tail lights, inside the trunk fastened with plastic nobs, pull back trunk trim panel.


Why 2000 Pontiac Bonneville want start with key but starts when - bypass?

See the answer to 2000 Bonneville Neutral Safety Switch Location. Had the same problem and that was my fix. You can install a separate Start Button in the Starter circuit to start the car also.


How do you take the inner side panel off of a 2000 Pontiac Bonneville SE?

http://www.a1electric.com/install/grand/grandam-3.htm This link provides some instructions on an alternative type of pontiac, however the basics remain the same.


How do you replace the horn button in a 1992 Bonneville?

You can replace the horn button on your 1992 Pontiac Bonneville by removing the center steering will cover. Remove the horn button retaining screws. Remove the horn button wiring harness. Reverse the process to install your new horn button.


On a 1999 Pontiac Bonneville how do you remove the lock from the latch on your glove box to install on new latch?

Open the glove box, unscrew the three screws next to the lock, tap lightly and it will come out.


How do you install a 1996 Pontiac Grand Am SE?

Install what?


How do you replace an idler pulley on a 1997 Ford F150 5.4ltr?

Remove serpentine belt. Remove pulley. Install new pulley. Install serpentine belt.


How do you install turbo-charger?

Honestly - buy one and have a professional install it or follow the instructions. Each system will be a little different and require different levels of technical knowledge and skill. One wiki-answer will not be able to tell you how to install any turbo-charger.


How do you install ignition lock cylinder in a 94 Pontiac Bonneville?

Attach the wiring harness to the end of the ignition lock cylinder. Slide the ignition lock cylinder into the slot. Tighten the retaining ring at the top of the cylinder.


How do you install a serpentine belt on a 1997 Pontiac Bonneville?

You have to remove the bottom bolt and spacer for the motor mount. Easiest way is to take the right front tire off, remove the inner fender well access flap. The bolt has a nut on the out side that has to be removed. Then the stud that goes through the mount into the engine has to be removed. Slip the belt over the pulleys and reverse the procedure. Thirty minute job.


How do to install oxygen sensor on 2006 Pontiac torrent?

We are asking how to remove and install a oxygen sensor for a2006 pontiac torrent.


How do you install air door actuator in 2003 Pontiac Bonneville Where is this part located?

There are four of these actuators in my 2000 Bonneville which has dual automatic temp controls. They are labeled: Air Mix Driver, Air Mix Passenger, Air Inlet, and Mode on HVAC Schematic. It would be necessary to know which one of these you were trying to remove.