0
Take a lightbulb so the bottom touches on end of a battery.
Take a wire and touch the battery and the other end to the lightbulb.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How did Benjamin Franklin invented the light bulb?
Benjamin Franklin did not invent the light bulb.
What year did he invent the light bulb?
Thomas Edison invented the first light bulb that was available for commercial use in 1879. The light bulb was first used in Menlo Park.
Who invented the light bulb first?
The person who invented the light bulb was Nikola Tesla look him up.
Did thomas jefferson invent the light bulb?
No. Thomas Jefferson did not contribute to the development of the light bulb. The light bulb has a number of inventors producing specific technologies that ended up being part of the light bulb including Humphrey Davy and Thomas Edison, who perfected it, and many others.
Who invented the light switch and light socket?
Thomas E. Murray
How do you change a light bulb when the piece it screws into twists with it?
This sounds like a household light socket you are inquiring about, replace the bulb and socket as well.
What is an Edison screw socket?
The screw socket into which an ordinary light bulb is inserted.
How do you replace brake lights in 1994 Nissan 300zx?
Remove brake light interior trim panels. Then you push and twist the socket for the brake light that needs replacing. Then pull out socket. then pull out bulb from socket and place new bulb in the light socket. Once bulb is installed into light socket. Place the socket where you removed it from brake light housing. Push and twist clockwise to lock back in place. Then replace trim panels.
Can dielectric grease be used on the contact point of a light bulb socket?
No, that would not be proper. The contact point of a light bulb socket has no need of any coating. A light bulb socket that is difficult to turn a bulb in will benefit from some light oil on the bulb threads prior to installing. Dielectric grease will harden, and is meant to insulate and protect electrical junctions from exposure and vibration.
What is the part called that a light bulb fits into?
Socket
What do you do if you break a light bulb?
If you break a light bulb in its socket, isolate the power (turn off the electric to that socket). Then use a needle nose pliers to get out rest of it with lamp off
How do you replace a brake light bulb in 2003 Honda Accord?
1. Open the truck and remove tail light compartment cover located at left/right up corners. 2. There will be two light bulbs: the one located on top is the brake light bulb and the lower one is for the backup light. 3. Twist the light socket and pull the light socket out; pull the broken light bulb out of the light socket and plug the new light bulb in (must get a right light bulb from auto parts store) 4. Test the new light bulb and put the compartment cover back on.
How do you replace the license plate lights on a 1999 Mazda protege?
Open the trunk. Turn the socket counterclockwise and remove. Then gently pull out the light bulb. Place the new bulb in the socket and replace the socket into the lens by turning clockwise. Replacement light bulb #3652.
What do a light bulb a hip joint and an eyeball have in common?
a socket
How can I make sure that the lighting will be suffcient for my home?
Check the amount of watts recommended for the light bulb socket and on the light bulb.
How do you replace the license plate light bulb on a 2002 Pontiac Grand Prix?
The license plate light bulb on a 2002 Pontiac Grand Prix is replaced by removing the retaining bolts and pulling the bulb out of its socket. A new bulb is then put into the socket and reassembled.
How do you change the center stop light on a ford 500?
To change the third brake light on a ford Five Hundred you first have to open the trunk. To access the bulb for the third brake light look under the housing below the light (from inside the trunk). There is a wire harness that runs into a socket. Twist the socket a quarter turn and the bulb and socket come out. Replace bulb and reinsert socket into the hole the quarter turn the socket to lock it back into place. Done!
