answersLogoWhite

0


Best Answer

go to your nearest aftermarket store or magazine and order the blocks or sut your springs and if ur not for sure how to do that then go to the nearest body shop and see what they can do

User Avatar

Wiki User

โˆ™ 2008-09-29 20:02:58
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: How do you lower a 1988 Mazda b2000 pick up truck?
Write your answer...
Submit
Related questions

Is a 1988 Mazda B2000 a 4 cylinder?

Yes, a Mazda B2000 is most definitely a 4-cylinder with a 2.0L engine. However, technically Mazda didn't produce the B2000 as a 1988 model. It was made in 1986-1987. Then in 1989 Mazda made the B2200 Pickup, which is a 2.2L 4 cylinder.


Is a 1988 Mazda B2000 carburated?

Yes, all B2000 models until 89 where carbureted. After 89 Mazda stopped production in the United States on this model.


What is the blue book value of a 1988 Mazda b22 pickup truck?

950.00


How do you adjust the clutch on a 1988 Mazda B2200 with a 5 speed?

At the top of the clutch pedal in the cab of the truck.


How much does a 1988 Mazda truck weigh?

The weight of the truck is on the driver side on the inside of the door jamb.Simply open your door and look down to the right.This will have the weight of the truck on a printed laminated sticker.


Where is the starter located on a 1988 Ford Ranger truck?

Lower rear end of the engine


How many bolts hold the starter on your 1988 B2000 pickup?

2 bolts hold it on


Where is the starter located on a full size 1988 Chevy truck?

Look at the lower rear end of engine


Where is the starter located on a 1988 Mazda RX7 With a Manual Transmission?

its on the tranny, drivers side lower porton of the bell housing


Where is the horn located on a 1988 Mazda b2200?

in the drivers lower fender well where the front bumber bolts up to the frame


Wiring of a 1988 Mazda rx7?

complicated


How do you know which piston is number one on a Mazda 1988 b2200?

It's the one closest to the crankshaft pulley, or the front of the engine, the front of the truck. Assuming it's an inline engine, not a v.


What are the specs for valve adjustment on a 1986 Mazda B2200?

Who is a valve calibration for mazda b2200 1988


What is the mpg on 1988 Mazda rx7?

I had a 1988 convertible that averaged 22-25 mpg.


Where is the temperature sensor on a 1988 Mazda B2200 pick-up truck?

It is located under the thermostat housing with a single wire connection.And the upper radiator hose goes to the thermostat housing.


When did the Mazda rx7 convertible come out?

1988-1991


Where is the fuel pump on a 1988 Toyota truck?

Fuel injected? In the fuel tank Carb. Lower front section of engine - follow fuel line from carb.


Do 1990 Chevy truck rims fit a 1988 Chevy truck?

Yes


Are the body panels from a 1988 Ford Laser TX3 the same as a 1988 Mazda 323 SS?

no


IS A 1987 CHEVY TRUCK DOOR INTERCHANGEABLE WITH A 1988 K5 BLAZER?

Are the door interchangeable on an 1987 chevy truck and an chevy blazer 1988


You have a 1988 Isuzu B2200 truck where is the fuel filter located?

Ummm no where??!!?! for one a b2200 is a Mazda pick up and in that case it would be on the drivers side half way back affixed to the inner side of the frame rail :P simalair location on either truck though


Why would the clutch not retract after you push it in on a 1988 Mazda B2000?

There is air in the clutch hydraulic system. This can be because the Master or Slave is bad, low fluid level, or it was not completely bled after installing a Slave or Master. Usually this problem is caused by a bad clutch slave which has leaked out all of the fluid. Kyrasis6 Owner of Mazdatruckin.com


Will a 1985 Mazda rx7 transmission fit a 1988 Mazda rx7?

Depends, which engine is in the 85, 13b or 12a?


Will a 1988 Chevy truck doorand anda bumper fit on a 1997chevy truck?

Yes it will


What is the best oil for a 1988 Mazda rx7?

royal purple