0
A. Here you go;
1. Turn the ignition switch on - between one and four seconds and press the trunk "Pop-Up" button on the transmitter while aiming the transmitter at the trunk. Between one and four seconds, turn the ignition switch off. Note: keep the timing between one and four seconds, too fast or too slow will cause the control unit to lose the stored codes.
2. Between one and four seconds, turn the ignition switch on. Between one and four seconds, press the trunk " Pop-Up " button on the transmitter while aiming the transmitter at the trunk. Between one and four seconds, turn the ignition switch off.
3. Between one and four seconds, turn the ignition switch on. Between one and four seconds, press the trunk " Pop-Up " button on the original transmitter while aiming the transmitter at the trunk. Between one and four seconds, turn the ignition switch off.
4. Between one and four seconds, turn the ignition switch on. Between one and four seconds, press the trunk " Pop-Up " button on the original transmitter while aiming the transmitter at the trunk. Leave the ignition switch on.
5. Within 15 seconds, aim the transmitter (up to three) whose codes you want to store at the trunk and press the " Pop-Up " button once on each transmitter.
6. Between one and four seconds, turn the ignition switch off.
7. Confirm proper operation with the new code(s).
NOTE:
"press the trunk Pop-Up button" means to press this button and hold
it until the little light on the transmitter comes on. You can use the same procedure with the Honda CRV remote as well (1997-99 models, not sure about later ones). Make sure the remote has FCC ID E4EG8DJ on the back.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
what is 2006 airbag model honda goldwing gl 1800?
what is a 2006 airbag model honda goldwing gl 1800
How to Program keyless remote 2006 Honda civic?
you have to take it to the dealer
How do you program a keyless remote for a 2006 Chrysler 300?
You have to have a scan tool.
How can you tell if your 2006 Ford F150 has keyless remote entry?
how do i program it
How do you program remote control for Ford Escape 2006?
NOTE: Make sure remote batteries are OKNOTE: All How_do_you_program_remote_control_for_ford_escape_hybrid_2005remote transmitters (15K601) must be programmed at the same time.NOTE: All previous transmitter identification codes (TIC's) will be erased when programming mode is entered.NOTE: To program (or reprogram) the keyless entry remote transmitters into the generic electronic module (GEM)(14B204), carry out the following steps.Turn the ignition from OFF to RUN eight times within 10 seconds, ending in RUN. If the GEM has successfully entered program mode, it will lock and unlock all the doors.NOTE: The first TIC must be entered within 7.5 seconds of entering the program mode and additional TICs must be entered within 7.5 seconds of the first TIC. The programming mode is exited whenever the timing constraints are not met.Press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed.If the door locks do not respond for any keyless entry remote transmitter, wait for several seconds and press the button again.Turn the ignition switch to the OFF position, or wait up to five minutes after step 1, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the GEM will lock and unlock all the doors one last time.
How do you program the remote for a 2006 Hyundai accent?
take it to the dealership doche bag
How do you program a keyless remote for 2006 dodge ram?
With the dealers scan tool.
How do program a keyless remote for a 2006 Buick Rainier?
Don't know for sure it will work with a 2006, but here is the procedure for a 2004: # Close all the vehicle doors. # Insert the ignition key into the ignition lock cylinder. # Press and hold the door unlock switch. # While holding the door lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF. # Release the door unlock switch. The doors will lock and unlock to confirm the program mode. # Press and hold the LOCK button and the UNLOCK button simultaneously on one transmitter. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter. # Repeat the previous step to program up to four transmitters. # Turn the ignition switch to the RUN position in order to exit the keyless entry transmitter mode. # Operate the transmitter functions in order to verify correct system operation.
How do you program a keyless remote for an Infiniti 2006 M35?
You cant take to dealership. Thats the only way sorry
How do you program a keyless remote Pontiac grand prix 2006?
go to http://www.programyourremote.com/ they have programs for many makes and models
How do you program the remote of a 2006 Cadillac STS?
You have to take it to a dealer and have them re-program it. My husbands dad works for a dealership and we tried to have them tell us how to do it but I believe they have to hook it to their computer to do it.
What is the gas mileage for a 2006 Honda goldwing?
Depends on how hard you ride. I guess around 40+.
