Chevy Blazer S-10

How do you remove a Chevy Blazer door panel?

373839

Top Answer
User Avatar
Wiki User
2015-07-15 19:05:37
2015-07-15 19:05:37

When removing the door panel, you need to remove all of the screws first. Then pull the door panel off. There should be screws around the edges or the door panel, and 1-2 screw on the door handle(on the inside). Then pop the door panel off, if the blazer has electric windows and locks you have to disconect them first, if it doesnt have power locks and windows, you have to take the window crank off,there should be a screw in the center of that. Unscrew the door lock and pull up. If it doesnt have them locks then you have to disconect it from inside the door panel

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

The 1998 Chevrolet Blazer door panel is held in place by eight retaining clips. Pry outward on each retaining clip to remove the door panel.

User Avatar

i think you should remove the door first then remove the door panel by hitting it with a soft hammer to release it.

User Avatar

Remove the inner kick panel. Disconnect the wiring harness. Drive the pins out of the hinges - remove door.

User Avatar

Using a screw driver remove the screws from the door panel, remove the clips, and pull the panel away from the frame slowly. Remove any wiring connectors, and remove the panel the rest of the way.

User Avatar

Using a screwdriver remove the screws and all of the clips in the door panel, and pull the panel away from the frame gently. Remove any wiring connectors, and pull the panel off the door frame.

User Avatar

Remove the screws in the door panel.

User Avatar

Dose the 2001 chevy blazer 4x4 4 door have a access panel to the fuel pump

User Avatar

You will need to remove the inside door panel of your 1993 Chevrolet Blazer. Remove the door handle linkage. Remove the door handle retaining bolts. Reverse the process to install the new door handle.

User Avatar

Take the door panel off and there are bolts inside.

User Avatar

Using a screw driver, remove the screws and the clips in the panel of the door and remove the panel gently. Remove any wiring connectors between the panel and the door, then remove the panel the rest of the way.

User Avatar

Remove the inside door panel of your 1987 Chevy. Remove the linkage from the door handle. Remove the door handle retaining bolts. The door handle will come off.

User Avatar

what steps are required to remove the inside door panel on a 1997 Chevy Malibu.

User Avatar

You will need to remove the inside door panel of your Chevrolet Blazer. Remove the window retaining clips. Put the window back into the window track. Tighten the window retaining clips.

User Avatar

Removing a 1991 Chevrolet Silverado door panel is pretty simple. All you will need to do is to remove the screws holding the door panel in place.

User Avatar

Chevy Tahoe remove front and rear speaker

User Avatar

any parts store should have tool to safely remove the pressure clips the secure the panel in place. Just slide the tool around the clip and pry out. you can pry it off by hand, but you can damage the clips and door panel.

User Avatar

The process for removing the door panel can be found at: http://www.bodyshopzone.com/archives/trim/door_panels/Chevy/Equinox_2005/dp_front_rear.html

User Avatar

You will need to remove the inside door panel of your 1988 Chevrolet Blazer S 10. Remove the door handle linkage. Remove the door handle retaining bolts. Reverse the process to install the new door handle.

User Avatar

The 2001 Chevy S 10 Blazer power door lock relay switch is located inside of the drivers side door. You will need to remove the drivers side door panel in order to access the door lock relay switch.

User Avatar

Removing the front door panel can be tricky. Remove the screws in the armrest, remove the bracket pin the wood trim, remove the armrest, remove the leather strip, disconnect any wires, remove the brackets and screws in the door panel and pull gently on the panel to remove it.

User Avatar

The interior door panel is held in place by 10 retaining clips and two screws. Remove the screws of which can be found by the door handle. Pry outward on each retaining clip to remove the door panel.

User Avatar

in my 99 you have to take the whole door panel off. Just unscrew the door handle on the inside and the little round tab where the door meets the car.

User Avatar

You will need to remove the inside door panel, by prying outward on the door panel retaining clips. When the door panel is removed the door handle assembly will be visible. Remove the door handle retaining bolts.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.