Yeah finally a question I can answer. I bought those pre cut tint on eBay and had to take the door apart and when I bought them side mirror with lights I had to remove the door compeletly. Well There are three hidden screw on both the front door and just one hidden one on the both the back doors. First the front doors. just pry very gently on the speakers and they just pop out, I could use my tumb and middle finger to pull on it and pops out. The hidden screw is located in of course where you open the door. There is a round shape cover. you just insert a tiny object like a needle or a ice pick and just pry out and the cover pops out very easy. there is a screw there, that it out. even though the door is open when your working on it, go ahead and pertend to open the door and slide that piece of plastic off. when you are putting it back together remember to do the same so the screw holes line up very easily. just pretend to open the door and slide that plastic on all the way. now at the bottom of the door there is a light cover. use your hand and just pull it out. it pops out very easy too. now for the hidden screw. use the ice pick or screw driver and where you stick your hand to close the door there is a rubber mate type thingy that holds the crums and dirt. pry the rubber gently half way and there is a screw there. Now start to unpop the door out and lift up and it will come lose easy. To take the door compeletly off there are only the five screw that is holding them on and they are visible between the door. Now the two back doors. there is the hidden screw in that rubber handle that you use to close the door with. that's it, then you just pry it and it pops out. Nothing to it really. Have fun. I love my Mazda 6 and have been taking it apart to add a bunch of cool stuff. Have a great day. Cheers
remove door panel, remove speeker.
Nobody knows.. Or they wont tell you... Have to take it to the mazda dealer...
1. Remove the rubberized armrest cover by prying it upward. 2. Remove (by prying out) the silver U shaped trim by the interior door handle. 3. Remove (by prying out) the sunken trim piece behind the interior door handle. 4. Remove the 10mm hex screws from where the armrest cover was and behind the door handle lever. 5. Pry the sides and bottom of the door panel loose. 6. Carefully lift up and out on the door panel and disconnect the wiring harness for the power locks & windows.
Take off your door and sell it to a hobo for a hammer then smash it with the hammer and it will come out easily ........................................................................................................................................................................................................................................................................................................but it wont go back on
Door speaker size. 6 X 9
1. Remove the door Pull-handle cover, by inserting a screwdriver into the access hole on the bottom of the handle, and using the screwdriver as a lever, pop off the handle cover. 2. Remove the button covering a retaining screw in the interior door latch backing plate. 3. Remove the 8 Torx� retaining screws around the perimeter of the door panel, and the single Torx� retaining screw in the interior door latch. 4. Remove the 2 hex bolts in the door handle. 5. Gently lift the panel upwards, to disengage the window weather-strip molding. 6. Remove the Door Latch Trim Panel, be sure to unplug the Power Lock Switch, and remember how the wire was run. 7. Remove the interior door latch, by gently pulling out on the front corner, which is held in by a plastic compression spring.
626
no they fit nuttella
To remove the air box on a 2007 Mazda 6, remove the nuts on the top of the box. Carefully place the nuts aside, and remove the top to access the filter or housing assembly.
This is the same front or rear door. 1. remove rubber insert at the bottom of the arm rest/door handle2. remove the 2. Philip head screws.3. run hand along bottom edge of door panel to ensure no other securing screws. 4. starting at the top rear edge of the door panel side a large flat screw drive/door panel tool(what ever you have) 5. lift sharply and you will here poping noises fromt the push clips lifting out of the socket.6. as you work down the rear edge of the door panel you will see the trim around the interior door handle lift away. remove it.7. the interior door handle will remain on the door. 8. remove the rest of the door panel.
big truck and a chain
hammer and strength