answersLogoWhite
Honda Prelude
Toyota Tundra
Honda Accord EX

How do you remove a glove box from 1985 Honda Prelude?

222324

Top Answer
User Avatar
Wiki User
2008-04-05 22:53:45
2008-04-05 22:53:45

Should be 3 8mm bolts along the bottom unscrew them (maybe 4, can't remember exactly) then you have to work with it to get around the stoppers, it also has little plastic pins on both sides that it pivots on. once you get it past the stoppers you should see the pins you just have to push in one side at a time to get it out

1

Related Questions

User Avatar

Not sure if 1987 is the same, but my 1985 Honda Prelude has the dipstick located in front of the radiatior, down kind of low.

User Avatar

under the dash left side by your left knee as seated.

User Avatar

under the car on the right side of the transaxel case,jackup the car and remove the fwd rt tire first.

User Avatar

Somewhere between the fuel tank and the engine. Get under the car and look.

User Avatar

The answer is no. The fuel-injected engine from your 1987 Accord is a direct-fit into a 1985-1987 Prelude Si, but will not fit into a 1988 or newer Prelude due to a completely different engine and transmission being used. The wiring harnesses and ECU will also be very different.

User Avatar

The dashboard of a 1985 Honda Civic is held together by a series of mounting screws. To remove the dashboard loosen all of the mounting screws. Pull the remaining clips off and take off the dash.

User Avatar

It Does Not Have A Gas Tank Drain Plug. You Will Have To Siphon The Gas Out. Or Drop The Tank With It In It. GOOD LUCK

User Avatar

It is a Honda Accord that was manufactured in 1985

User Avatar

try the12volt.com i know for a fact thay have one Try http://www.ahdol.com/ for the diagram.

User Avatar

To replace the heater core of a 1985 Bronco 2, open the glove box and push on the 2 tabs that hold it in place. After removing the entire glove box, remove the round plastic screws of the heater core. Remove the old and replace with a new one.

User Avatar

To change the headlight on a 1985 Honda Spree scooter remove the headlight housing. The scooter headlight will be mounting on the rear of the housing. Remove it and replace the bulb.

User Avatar

Remove all screws and plugs. You will need a small flathead screwdriver to 'pop' the pin that holds the window winder in place ( behind it) then pull the bottom of the door trim outwards and lift it upwards. wind window all the way down first so not to scratch the glass as you remove the trim.

User Avatar

Gasper Glove Company made Michael Jackson's glove in 1985.

User Avatar

If your car has never been retrofitted with R-134a, then chances are you won't be able to get the refrigerant. (R-12) It needs to be done by a pro.

User Avatar

Yes Honda civics do have interference engines.HONDA1986-87 1.0L Prelude1973-78 1.2L All1973-78 1.3L All1980-84 1.3L All1973-78 1.5L All1985-89 1.5L Civic1988-95 1.5L Civic, CRX1993-95 1.5L Civic Del Sol1979-84 1.5L All1985-87 1.5L CRX1993-95 1.6L Civic Del Sol1973-78 1.6L All1980-82 1.6L All1988-95 1.6L Civic, CRX1984-87 1.8L Prelude, Accord1979-83 1.8L All1986-91 2.0L Prelude1990-91 2.1L Prelude1990-95 2.2L Prelude, Accord1992-95 2.2L Prelude1995 2.7L Accord

User Avatar

Eng oil capacity 1985 Honda 200 m atc?

User Avatar

The PCV valve on your car is mounted on the valve cover and has a rubber hose that is connected to the fresh air intake.

User Avatar

The Equalizer - 1985 Prelude 2-1 was released on: USA: 8 October 1986 West Germany: 30 March 1988

User Avatar

Remove the water supply lines to your 1985 Pontiac Trans Am heater core. Remove the heater core retaining bolts. The heater core will come out. Reverse the process to install your new heater core.

User Avatar

Honda Legend was created in 1985.

User Avatar

Honda Today was created in 1985.

User Avatar

hi, you may find that it dose not have a clutch cylinder, as this model usually has a cable. confirm this by following thru from top of clutch pedal. regards razzel

User Avatar

* Remove the ashtray and ashtray holder * Remove the radio and mounting plate screws and lower the radio and unplug the electrical connector and antenna lead then push the radio out of the dashboard


Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.