Ford Ranger
Ford F-150
Ford Ranger XLT

How do you remove a passenger door panel on a 1997 Ford Ranger?


Top Answer
User Avatar
Wiki User
2006-10-28 02:04:17
2006-10-28 02:04:17

remove the window handle, remove screws from armrest, remove the inner door handle and the screw on the lower rear of the door panel, lift the panel upwards to remove from the slots along the bottom of the door.


Related Questions

It's in the passenger footwell by the kick panel

In the front passenger footwell by the kick panel

I have a 2000 Ranger and the reset button is in the passenger side kick panel. If you look between the glovebox and the floor it should have "Fuel Reset" labeled on the kick panel.

The 1997 Ford Ranger ECM computer is located behind the dashboard. The computer will be on the passenger side of the passenger compartment.

The front passenger quarter panel on a 1997 Honda Civic is taken off by removing all of the mounting hardware. Lift the hood and locate all the mounting bolts on the inside is remove them. Check under the vehicles for dust coves and remove them. Open the door and remove the bolts. Once all mounting hardware is removed pull the fender off.

On a 1997 Ford Ranger : Open the drivers door , and IN the end of the dash you will see a removable plastic fuse panel cover ( the fuses are behind the cover )

do you have to remove fan shroud to access thermostat housing on a 1997 2.3L ford ranger

Bank 1 is the passenger side of the V6 engine in a Ford Ranger

Door Panels Removal & Installation 1. Remove the sail panel. 2. Remove the door panel by carefully lifting the panel upward to release the retaining clips. 3. Remove the electrical plugs that control the windows, exc. (Replace mirror) 4. The installation is the reverse of the removal.

No. To remove the widow its easiest to remove the outside panel

what steps are required to remove the inside door panel on a 1997 Chevy Malibu.

Remove the inside door panel. Remove the window clips that hold the window onto the track. The window will come out. Reverse the process to install the new window.

there are Allen head screws all the way around the panel remove these and the inside close handle bezel which you can pop off to get to 2 screws behind it. once done lift it up

In order to remove the rear door panel of 1997 Mercedes Benz e420, you need to drill out the rivets that hold that hold the door panel. Once that is done you should remove the panel in a careful manner so as not to break the plastic clips.รŠ

How to replace a clutch interlock switch on a 1997 Ford Ranger XLT

Remove the door and window handles. You may need a special tool from the parts store. Then take out all of the screws you can find then remove the retainers on the sides and bottom of the door panel again with a aspecial tool available at the parts store.When all is loose, pull out on the bottom of the panel and press in at the top to disengage the top from the door.

remove the bolts holding on the plastic paneling under the steering wheel in the interior. remove the two bolts connecting the hood release latch from this plastic panel. then remove the panel. the circuit opening relay is under this panel, and is green(in my 1997 tacoma).

On a 1997 Ford Windstar : The jack is supposed to be in the cargo area , behind a removable panel on the passenger side

On a 1997 Ford Explorer : The right side kick panel would be inthe front passenger footwell It is the interior trim panel , just in front of the front door , by the passengers feet

In the right front passenger footwell , by or behind the kick panel

In the front passenger footwell BEHIND the kick panel according to the 1997 Ford Explorer Owner Guide . On my 1995 Ford Explorer it is BY the kick panel in the front passenger footwell , just above the carpet in the corner

You can see the blueprint of the door on a 1997 Grand Marquis/Crown Victoria at the related link below. This will aid in the removal of the panel.

You should be able to find the on/off switch under the passenger side kick panel, take a flash light and look over the top of the kick panel and you should see it there. If not remove the door sill and then the kick panel to expose the switch.

Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.