0
You will need a gear puller to pull it off . Sometimes you can take a hammer and tap it off but usually will not work .
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How do you repair a crankshaft pulley for a 98 Saturn SC2 DOHC?
u need to buy new pulley then, remove serpentine belt from engine remove bolts that hold pulley to crankshaft remove pully instalation is exact opposite of removalAnsweru need to buy new pulley then, remove serpentine belt from engine remove bolts that hold pulley to crankshaft remove pully instalation is exact opposite of removal Answeru need to buy new pulley then, remove serpentine belt from engine remove bolts that hold pulley to crankshaft remove pully instalation is exact opposite of removal
How do you remove and install a 1998 Nissan altama idler tension pulley The pulley the space between the pulley and body of car is only about an inch does not have enough room to pullout?
The idler pulley is mounted on a plate that needs to be removed. In order to remove the plate with the idler pulley, you must remove the engine mount to get out the idler pulley. To remove the engine mount, you need to jack-up the engine from the bottom of the oil pan (Note: place a piece of wood plank between the bottom of the oil pan and the jack). The idler pulley is mounted on a plate that needs to be removed. In order to remove the plate with the idler pulley, you must remove the engine mount to get out the idler pulley. To remove the engine mount, you need to jack-up the engine from the bottom of the oil pan (Note: place a piece of wood plank between the bottom of the oil pan and the jack).
How do remove a 1996 Chrysler damper pulley?
Depending on engine displacement in general remove belt-s then bolt holding pulley to the crankshaft then using a puller remove the pulley, when installing use a installer not a hammer to put the pulley on the crankshaft.
How do you remove crank shaft pulley of 6d14-1a engine?
if you dont have the correct puller,you can remove it by tapping the smaller pulley inwards [towards rear of block] with a block of timber,so as not to damage pulley and a 5lb hammer at opposite sides of pulley,example 9 to 3 oclock position.until the small locking cone inside the small pulley becomes loose. you might have to give it a few sharp blows but it will loosen as i have done it a few times.
How do you remove engine crank pulley 1998 jetta?
Loosen the 18mm bolt about 4 or 5 mm and give the bolt a good wack and the pulley should pop. Then remove the bolt and pulley.
How do you replace the water pump belt pulley located on a 1991 Buick Park Avenue?
You have to remove the engine mount next to it, then remove the 4 bolts in the pulley
How do you replace the idler pulley on 1992 350 engine?
Remove the old, damaged idler pulley and replace it with a new one.
How to replace the tensioner pulley on a 2001 galant gtz?
Remove air box, pulley is located just under attached to engine block. Should remove bolts take off belt, and replace pulley and belt.
How do you remove crankshaft pulley Mazda 626 1993?
Im not sure which direction the bolt turns to remove the pulley...the crank shaft turns in clock wise direction when engine is running.
How do you get the serpentine?
To get the serpentine belt off an engine fan, loosen the tensioner pulley. This pulley is the one with a bolt in a slot that can be adjusted. Then remove the belt.
How do you remove the crankshaft pulley?
In most cases you need a pulley puller. Need to know make, model , year and engine to help you more.
How do you remove the power steering pulley from a 2002 Chevy Suburban w 4 wheel drive?
This requires a special tool to remove and install the pulley. Most auto parts stores should have one in stock Best to remove the pulley with the pump removed from the engine compartment.
