0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you remove the radio from a Rover 25?
Removing a radio from a Rover 25 is easy and quick. All you have to do is remove the trimming with a flat head screw driver, unscrew the panel, take off the panel, unscrew the radio, then take out the radio.
Is it a Honda engine in rover 25 car?
onda engine was in the rover 25
How do you change bulb on a rover 25?
how to change headlamp bulb on rover 25
Where do you top up coolant on a rover 25?
Where do i top up my coolant on a rover 25
How do you locate and replace a thermostat in a 2000 rover 25?
how do you replace a thermostat in a rover 25
How do you disable your rover 25 car alarm?
how do you disable rover 25 car alarm
Is a rover 25 1.4 injection faster than a rover 25 1.8 injection. because i have a rover 25 1.8 injection and my uncle says his rover 1.4 would beat mine so can it?
ja
What is the name of one company which has a Rover 25 for sale?
The one company which does have a Rover 25 for sale is the MG Rover Group. Purchasing from the Rover Group direct will enable you to save money on your purchase.
How do you remove the Blower Motor on a 2000 CLK Mercedes Benz?
remove right side under dash panel remove blower cover unplug motor remove motor and blower regulator swap regulator on to new motor note all u need is a philpps head and a 15 and 25 torques
Where is the starter located on an 1990 eagle talon tsi 5 speed?
And instructions thanks to Autozone.com: Disconnect the negative, then the positive battery cables from the battery. For 1990-94 vehicles, remove the battery and battery tray from the engine compartment. For 1990-94 vehicles, detach the speedometer cable connector from the transaxle. Detach the starter motor electrical connections. Unfasten the starter motor mounting bolts, then remove the starter from the vehicle. Clean both surfaces of starter motor flange and rear plate. Install the starter motor onto the engine and secure with the retainer bolts. Tighten the retainers to the specifications shown in the accompanying figure. Attach the electrical harness connector(s) to the starter. If removed, install the intake manifold stay and tighten the retainers to 18 ft. lbs. (25 Nm). For 1990-94 vehicles, attach the speedometer cable to the transaxle. Install the battery tray and battery. Connect the positive, then the negative battery cables. Operate the starter to assure proper operation.
Where is the starter motor on a 1997 escort 1600?
Sorry I forgot to sign in before posting my answer... Plus they wouldn't allow me to put in the photos, that would show you where it was, either, so sorry about that.... Best of luck!The Starter 'Motor' is the starter, so it may need replacing...Here's how to do that:1.8L Engines REMOVALDisconnect the negative battery cable.Remove the air cleaner-to-intake manifold tube.Remove the upper starter motor bolts.Raise and safely support the front of the vehicle securely on jackstands.Unfasten the intake manifold starter support bolts and remove the support.CAUTIONWhen disengaging the plastic hard shell connector at the solenoidS terminal, grasp the connector and depress the plastic tab, then pull off the lead assembly. Do not pull on the lead.Disengage the S terminal connector from the solenoid.Unfasten the solenoid B terminal nut and disconnect the cable from the terminal.Unfasten the lower starter motor bolt and remove the starter motor from the car.To install:WARNINGMake sure the starter drive housing pilot diameter is fully engaged in the cover plate locating hole and that all mounting surfaces are flush.NOTE: Install the upper starter motor bolts first to prevent binding or a noisy starter motor.Place the starter motor in position, install the upper mounting bolts and tighten them to 18-20 ft. lbs. (25-27 Nm).Engage the S terminal connector to the solenoid.Connect the B terminal wire and tighten the nut to 80-120 inch lbs. (9-13.5 Nm).Install the lower starter motor bolt and tighten it to 18-20 ft. lbs. (25-27 Nm).Install the intake manifold starter support and tighten the bolts to 27-38 ft. lbs. (37-52 Nm).Lower the car and connect the air cleaner-to-intake manifold tube.Connect the negative battery cable1.9L EnginesDisconnect the negative battery cable.On models equipped with an automatic transaxle, remove the accelerator (kickdown) cable routing bracket from the block.WARNINGWhen disengaging the plastic hard shell connector at the solenoidS terminal, grasp the connector and depress the plastic tab, then pull off the lead assembly. Do not pull on the lead.Disengage the S terminal connector from the solenoid.Unfasten the solenoid B terminal nut and disconnect the cable from the terminal.Unfasten the starter motor retaining bolts and remove the starter motor from the car.To install:NOTE: Make sure the starter drive housing pilot diameter is fully engaged in the cover plate locating hole and that all mounting surfaces are flush.Place the starter motor in position, install the retaining bolts and tighten them to 18-20 ft. lbs. (25-27 Nm).Engage the S terminal connector to the solenoid.Connect the B terminal wire and tighten the nut to 80-120 inch lbs. (9-13.5 Nm).On models equipped with an automatic transaxle, install the accelerator (kickdown) cable routing bracket on the block.Connect the negative battery cable2.0L Engines SOHC ENGINESDisconnect the negative battery cable.Remove the air cleaner outlet tube.Remove the two top starter motor bolts.Raise the car and support it with safety stands.NOTE: A protective cap is covering the B terminal and must be replaced after servicing the starter motor or solenoid.Tag and disengage the S terminal wire and the B terminal nut and cable from the solenoid.Unfasten the lower starter motor bolt and remove the assembly from the car.To install:Install the starter motor assembly and tighten the lower mounting bolt to 18-20 ft. lbs. (25-27 Nm).Attach the S terminal wire, B terminal cable and nut. Tighten the nut to 80-120 inch lbs. (9-13.5 Nm).Lower the car and install the top starter motor bolts. Tighten the bolts to 18-20 ft. lbs. (25-27 Nm).Install the air cleaner outlet tube.Connect the negative battery cable.DOHC ENGINESDisconnect the negative battery cable.Remove the air cleaner outlet tube.Raise the car and support it with safety stands.Unfasten the lower starter motor bolt.Lower the car and unfasten the two starter motor upper bolts.Raise the car and support it with safety stands.Slide the starter motor from its mounting until you can gain access to the wiring.Unfasten the nuts and remove the integral connector.Remove the starter motor from the carTo install:Install the integral connector and tighten the retaining nuts to 61 inch lbs. (7 Nm).Engage the starter motor to its mounting.Lower the car and install the two starter motor upper bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm).Raise the car and support it with safety stands.Install the lower starter motor bolt. Tighten the bolt to 15-20 ft. lbs. (20-27 Nm).Lower the car and install the air cleaner outlet tube.Connect the negative battery cableTHESE INSTRUCTIONS ARE FOR A 1997 FORD ESCORT ONLY...I really hope that this helps you and others to get the jos done!Let me know...
Where is the timing marks rover 25 1.4?
can you tell what are the marks for a rover 25 14 on a 52 reg for got to mark it up thanks
