answersLogoWhite
Toyota Camry
Chevy 305
Chevy Blazer S-10
DIY Projects

How do you remove a starter on an 88 Toyota Camry 2.0 liter 4 cylinder engine?

108109110

Top Answer
User Avatar
Wiki User
2015-07-15 21:41:45
2015-07-15 21:41:45

You just disconect the wires and then take out the bolts holding it in. Remember to always disconnect the battery.

1

Related Questions

User Avatar

The starter on a 1998 Toyota 4runner is held located on the transmission housing. The starter is held on by 2 bolts which mount it directly it the engine. Remove the two bolts to replace the starter.

User Avatar

Remove wiring remove the 2 bolts holding the starter to the engine,remove the starter,you might want to remove the air filterhousing and inlet hose.

User Avatar

get a tap and die set and follow the instructions.

User Avatar

6 cylinder? Lower rear end of engine4 cylinder ? front of engine behind radiator lower section Disconnect the - battery cableRaise and support vehicleRemove wiring harness at top of starterRemove mounting boltsRemove starter

User Avatar

Remove - battery cable Raise and support vehicle Remove wires from top of starter Remove mounting bolts Remove starter If you cannot get to the wires there is enough wire to remove the starter and then remove the wires

User Avatar

disconnect battery. remove cables at the starter. remove starter mount bolts. remove starter. replace starter. reinstall bolts. reinstall wires. reinstall battery cable.

User Avatar

If it is a 6-cylinder engine the starter is at the "front" of the engine about 10 inches behind the bottom of the radiator. You have to jack up the front of the car and remove it from underneath.

User Avatar

Starter of toyota corolla and matrix is not the same. The best thing you do if you change your starter by yourself is to remove and compare to the new starter.

User Avatar

You should remove the positive cable from your 1996 Toyota battery. Remove the cables from the front of the starter. Remove the starter retaining bolts. Reverse the process to install the new starter.

User Avatar

disconnect neg.cable,then disconnect pos. cable from starter ,then other wire,then remove 2 bolts holding starter to engine.

User Avatar

Disconect the - battery cable Raise and support vehicle Remove wiring at the top of starter Remove mounting bolts Remove starter

User Avatar

Remove a battery connector. Remove the starter and put another in it's place.

User Avatar

Locate the starter at the rear of the engine on the passenger's side. Unplug the wiring. Remove the bolts that hold the starter. Remove the starter.

User Avatar

remove neg.cable.then positive cable cable from starter,remove male to female wire ,then remove 2 bolts holding starter to engine.

User Avatar

Remove the negative battery cable. Follow the posative cable down to the starter. remove the wires then the bolts holding it to the engine. Label the wires to make sure they go back where they came from.

User Avatar

Disconnect battery. Remove air filter assembly. Remove brace from intake manifold to engine block next to starter. Remove the two wires from the starter. Remove the two bolts holding the starter. One at the bottom the other at the top from the transmission side. The reason for removing the air filter assy.

User Avatar

For the ones on the side you may have to remove the engine mount or starter. For the ones on the back you will have to remove the transmission.

User Avatar

For the 2.2L engine, remove the starter. The sensor is screwed into the engine block behind the starter with a 10mm bolt. The wiring plugs into the front of the sensor facing the radiator.

User Avatar

Disconnect the - battery cable Raise and support the vehicle Remove wiring at the top of starter Remove mounting bolts Remove starter

User Avatar

Disconnect battery. Remove air filter assembly. Remove brace from intake manifold to engine block next to starter. Remove the two wires from the starter. Remoye the two bolts holding the starter. One at the bottom the other at the top from the transmission side. The reason for removing the air filter assy.

User Avatar

Disconnect the - battery cable Raise and support vehicle Remove wiring at top of starter Remove starter mounting bolts Remove starter

User Avatar

how to remove the starter from a 92 s-10 4x2 with a 2.8 engine

User Avatar

remove plastic engine cover on right side of engine . on top of starter is the battery nut . remove carefully making sure the stud does not spin . then remove 2 bolts at rear of starter . gentlly pull starter out of mount .

User Avatar

Should be at the lower rear end of the engine Remove the - battery cableRaise and support vehicleRemove wires from starter solenoid at top of starterRemove starter mounting boltsRemove starter


Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.