0
How do you remove all three bolts on power steering pump with the motor mount in the way 98 old achieva?
Wiki User
∙ 12y ago
you cant! believe me you can remove two but the last one you have to remove motor mount . jack up motor then remove top three motor mount bolt then look under tire wall you should see two 10mm bolt loosen and the whole mount assembly will lift out you should have enough room then to work with.
note.i just change my Power Steering pump because car whine when idle and only got louder after excelleration. well the whining noise turn out to be ac compressor i think your going threw same issue if it hard to determine rather it power steering or water pump because of type of noise it the ac
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
How do you remove the 3 bottom bolts out of the water pump located on a 1995 Buick Riviera?
you have to remove the motor mount and power steering pump
How do you change drive belts on 1967 Cadillac deville?
CHANGING ALTENATOR BELT: 1. loosen compressor bolts push towards engine to remove compressor belt 2. loosen power steering bolts and push pump towards engine to get slack to remove belt. 3. loosen altenator bolts pus it towards motor to get slack and remove belt. 4. put new belt on push altenator away from motor to tighten slack in belt and tighten bolts 5. push power steering pump away from motor to tighten belt and tighten bolts 6. push compressor away from motor to tighten belt and tighten bolts. REMOVE FAN BELT: Do steps 1,2,5 and 6 REMOVE COMPRESSOR BELT: Do steps 1and 6
How do you replace a serpentine belt on an 97 Olds Achieva?
replacing achieva serpentine on a 96i have a 96 and you have to completely remove the motor mount and all of the bolts holding it on the engine to replace the belt,also carefully jack up the engine since it will fall on the ground if you take off the mount
How do you remove power steering pump from a 1995 Lumina APV?
remove motor mount from right side of motor ,remove belt ;use 13mm socket to go in pulley holes of pump; should be three bolts at 2 o'clock 4o'clock and 7o'clock positions
Where is the blower motor located on a Oldsmobile achieva?
where is the blower motor located a a 1997 oldsmobile achieva
How do you replace a rack and pinion on a 1997 Dodge Intrepid?
You must remove the wipers, cowling, wiper motor and linkage assembly. Then you will remove the power steering lines, connectors and tie rod ends. Next, remove the bolts holding the rack to the body of the car, then remove it through the hole where the wiper motor and linkage assembly was located.
How to remove ford ranger window motor?
remove door panel u will se 3 dimples in the sheet meatl where the motor is drill out 3 10 mm holes to axcess the 3 8 mm bolts remove bolts and then u can remove the motor pretty easy
How do you replace 1991 astro van motor mount?
Use a jack with a board on top to support the engine. Loosen the bolts for the motor mount. Raise the engine slightly then take the bolts out and remove the motor mount. Install the new mount, tighten the bolts, then remove the jack.
How do you remove the power window motor passenger side on a 1987 Bronco II?
just did this on a 1988 bronco II. I did the following: remove door panel carefully remove plastic water proof sheet...do not tear...so you can reuse. to remove the motor, i had to drill access holes to get to the three bolts that attach the motor to the regulator. these are 8mm bolts. I located the three bolts and I drilled 1/2 inch holes to access the bolts...this allowed me to remove the motor from its mounting...then unplug from wiring harness.
How do you remove a passenger motor mount?
in removing motor mount what bolts need to be removed. This is a 1998 biuck regal 3.8L, and I am not sure how to remove the motor mount.
How replace the wiper motor Honda Civic?
Remove the wiper arm from the wiper motor. Remove the wiring harness. Remove the wiper motor retaining bolts. Reverse the process to install the new wiper motor.
How do you change the wiper motor on a 2002 a4?
Remove the wiper arm from the wiper motor. Remove the wiring harness from the wiper motor. Remove the wiper motor retaining bolts. Reverse the process to install the new wiper motor.
