0
The year, make and model would help.
Wiki User
∙ 8y ago
Add your answer:
Earn +20 pts
How do you replace transmission on 2000 ford windstar?
The best way to replace the transmission in your 2000 Ford Windstar is to drop both the motor & transmission, Here are the instructions, Disconnect All wiring from engine and trans. Move wiring harness away. disconnect fuel lines at the fuel rail next to intake. remove starter. remove power steering lines. evacuate AC and remove ac lines.drain radiator remove hoses. remove radiator. Raise vehicle. remove starter remove exhaust pipes @ manifold. un plug 02 sensors remove the bolts on Torq converter. remove all bolts on trans. including trans mount bolts . The HARD part is having something to lower the cradle on. You have to lower both engine & trans then R&R the trans.
How do you change a radiator on a dodge stratus?
you will have to support engine for this i have found...next drain your coolant and undue hoses. remove font engine mount that is located near the trans and in front of starter...should look like a big circle...then loosen and remove the ac pump but do not remove the ac lines as this will evacuate the system and do so in a hurry....then there will be 2-3 holes in the upper core support leading to the upper radiator retaining mounts...remove the bolt and you should see the radiator "lean" forward making it accessible......depending on year or originality of the vehicle you will have transmission line to remove, if not then you can now lift out the radiator.
How do you remove and replace the radiator in a 1994 ford F 150?
First drain it from the drain cock, then unbolt the fan shroud and remove it (this may require you to remove the water pump fan), next remove the radiator hoses (top and bottom), remove the overflow hose, undo the transmission cooler lines (for automatic transmissions only). Now you can unbolt the radiator and lift out. Installation is reverse of removal.
How do you remove the radiator from a Honda Civic?
It can be very simple to remove the radiator from a Honda Civic. The first step is to drain the coolant from the radiator. The next step is to disconnect the cooling fan switch and remove the hoses. Then the cooling fan should be removed. Then the radiator should be unbolted and lifted carefully from the vehicle.
How do you remove the radiator on a 96 Sunfire?
The radiator on a 1997 Mercury Mountaineer is removed by draining the coolant, disconnecting the radiator hoses, and unbolting the shroud. The retaining bolts are then removed and the radiator is lifted from the vehicle.
How do you replace a radiator on a 2000 GM jimmy?
Caution:On models equipped with Delco-Loc 2 or Theftlock audio systems make sure you have activation code * Disconnect the negative battery cable * Drain the cooling system * Disable the airbag system.Disconnect the forward discriminating sensor harness from the front fenderwell.It may be necessary to remove the hood latch mechanism in conjunction with the airbag sensor and secure them together and out of the way during the radiator removal * Remove the cooling fan assembly * Disconnect the upper and lower radiator hoses from the radiator then disconnect the coolant recovery hoses at the radiator neck * Remove the automatic transaxle cooler lines if equipped from the left tank of the radiator * Remove the hood latch support from the upper tie bar on the front of the engine compartment * Remove the right and left headlight assemblies from the vehicle * Remove the condensar mounting bolts from the radiator assembly * Remove the tie bar (crossbeam) from the engine compartment * The radiator can be removed from the top with some wiggling to clear various components
How do you replace speed ometer gear on78 Chevy truck?
you have to find the speedo cable on the side of the trans near the rear. unscrew the speedo ring on the cable and pull the cable out of the trans. then remove the small bolt and clamp on the trans right next to where the cable was. this allows you to remove the speedo gear. it may be hard to remove as it has an O-ring sealing it in the trans. on 4x4 I think the cable goes to the transfer case instead of the trans. but otherwise same process.
How can you uninstall a radiator from a 2000 Dodge Dakota?
you have to remove the fan this takes a specail tool then you will drain the radiator with the plug that's on the bottom corner of the radiator next disconnect the upper and lower hoses it should come out
How is the bottom portion of the radiator connected on a 97 Ford E150 for removal?
Your radiator has a top and botton hose connection, you must remove them first. Be sure to catch the coolant with a large tub or dishwasher pan. second, there is a top and bottom oil cooler connection, you must remove them. Be sure to catch the oil with a pan and discard properly Third, you may have an air conditioner condensor in front of the radiator. you should not have to remove this, it creates a lot of cost and trouble. Just be careful of it and the tubing when removing the radiator. The a/c hoses may be attached to the radiator shroud. fourth, there is a cover on top of the radiator, remove that cover> Next remove the fan shroud, and remove the fan and clutch. You may have to remove the fan blade first, and the shroud second. The bottom of the radiator sets in a cradle. After the above equipment is removed, the radiator should come straight up. It will probably need some coaxing, and the rubber cushion at the bottom sometimes bonds to the metal. Be very careful of the air conditioner condensor and lines. moving them can break the seals and require recharging. JOEDI
How do you remove and install automatic transmission in a 1995 4X4 V6?
Really need to know make/model/trim to give a more accurate description... but in general. Remove the trim around the shifter, remove shift knob and same with transfer case shifter(if manual).. Then you need to lift the vehicle, may need to remove the exhaust system if V8(like on BMW's), disconnect any cooler lines, sensor/wires. Disconnect/ strap out of the way or remove the driveshafts. Unbolt remove the transfer case from the transmission. Unbolt the torque converter, and with the trans supported with a trans jack, unbolt the trans mount/cross member. Place a jack stand under the front of the motor to help support/tilt it to make it simpler to remove the transmission. Next you will need to unbolt the bell housing and wiggle/pry the transmission off the engine. Then swap trans/torque converter, would flush any coolers/lines. Follow steps in reverse to reinstall, check fluid following manufacturer's specs.
How do you change the radiator hoses on a Honda VTX 1800 motorcycle?
Do this on a cold engine. Remove the radiator cap. Then remove the clamps holding the upper radiator hose in place as it attaches to the radiator and the thermostat housing. Next remove the clamps that hold the lower radiator hose and then remove the hose itself. The clamps are easily removed with a screwdriver. Replace the old hoses with new ones and fasten them in place with preferably new clamps. The coolant will have drained out and has to be replaced after fitting the new hoses. Check for air in the cooling system.
How do you change the clutch on a 1992 paseo - Does it require engine removal?
Changing the clutch is a big job. If you don't have a lift and tranny jack I wouldn't recommend attempting the repair. If you have the right setup it does not require engine removal. However, you could remove the engine and trans together and then separate them outside of the engine bay. First, you need to remove the ball joints. This is done by removing the wheel and using a ball joint separator tool. Its a "U" shaped tool that fits underneath the ball joint boot. There is an air tool that can do this. Once you remove the ball joint, you need to remove the driveshaft from the hub. This is done by holding the hub assembly by the brake rotor and pulling towards yourself. The driveshaft may come out of the trans first so be careful not to damage the spline on either end of the driveshaft by dropping it. Once the driveshaft is removed, repeat this procedure on the other side of the front end. You need to remove the slave cylinder from the clutch fork. Two 10 mm bolts hold it on. Next, remove the shifter cables. Now with , you can start removing the trans bolts. First, support the trans from the bottom with the jack. Next, remove the trans to body mount. This bracket is located near the battery. If you look in front of the battery you will see it. Remove and check the jack. You may need to adjust the jack to support the weight of the trans. Next, remove the trans to engine bolts. Look for where the casing for the trans and engine block meet. You will find the bolts there. Remove all the bolts and the trans should start to move a little. With the jack supporting the trans, start to move the trans away from the engine block. Once you have separated the trans from the motor, lower the jack slowly making sure the trans is balanced on the jack plate. Get the trans to a stand or appropriate resting place to remove the clutch assembly.
