0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Can you remove a transmission on a 2001 Eclipse without removing the right Transaxle?
The car has only one transaxle, AKA transmission, then no, you cannot remove the tranny without removing the tranny. If you mean without removing CV Axle or drive axle or Axle shaft or CV shaft (same thing) then the answer is still no. You cannot remove the transaxle without removing the drive axle/CV shaft.
Who won the Triple Crown 2010?
As of the date this question was asked -- May 14, 2010 -- the only leg of the Triple Crown that has been run is the Kentucky Derby, on May 1, 2010, won by Super Saver.
How do you remove the front right axel of a Mazda tribute 2002?
Remove the wheel and the brake caliper. Remove the two 18mm bolts that hold the brake caliper bracket, and remove it and the rotor. Remove the small bolt that holds the antilock brake sensor and remove the sensor. Remove the 32mm axle nut. The nut may be hard to remove but it is right hand thread. You can remove the two 18mm bolts from the bottom of the strut and swing the whole wheel bearing assembly out just barely far enough to remove the axle without removing the lower ball joint. The axle is splined in the wheel bearing assembly and you can knock it out with a block of hard wood and a hammer. Reach back along the axle with a long extension and remove the two nuts holding the axle carrier bearing. Be careful not to let the axle fall down and damage the axle seal in the transmission. The axle should slide easily out of the transmission and only a tiny bit of fluid will leak out. Hope this helps. Good luck.
How do you Remove a left rear axle on Honda 2002 350 es 4X4?
There's only one axle...not a left and right. Buy a Honda service manual before you tare it up.
How do you change rear axle brearing on a suzuki quadracer?
You only need to remove the left hub assembly. Loosen the axle nut while still on four wheels. Having said that, put rear on suitable stand forward of the rear axle bearing carrier. For ease remove both rear wheels. Remove drive chain. Remove left hub. Remove brake caliper and secure. Remove the rear sprocket with flange together. There are two nuts on the axle that holds this in place. The nuts are different. The outer nut is a lock nut. Remove the outer and remover the inner nut. You can now slide the axle shaft out of the bearing housing. Now remove the housing after loosening the retaining bolts. Take the housing to a bench and remove seals and bearing. Note that there is a long spacer separating the bearing which is in the middle. This how I did this on my 86. Regards
Is there an access panel for the fuel pump on a 1992 ford crown vitoria?
Yes, but only when you remove the fuel tank.
How do you change rear brakes 1982 ford e250van with full floating axle?
the only difference to changing brakes with a full floating axle , is that you dont have to remove the axle the brake drum will come off the hub with out removing the axle. you may have to get underneath and back off the brakes to free it up enuff to move the drum
How do you change a craftsman riding lawn mower tire?
TO REMOVE WHEEL FOR REPAIRS • Block up axle securely. • Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose). • Repair tire and reassemble. • On rear wheels only: align grooves in rear wheel hub and axle. Insert square key. • Replace washers and snap retaining ring securely in axle groove.• Replace axle cover.
Would the drive shaft connect to the rear axle?
Only if the rear axle is a drive axle.
How to remove a 1990 Acura Integra alterntor?
do you want to know how to remove your alternator? i have a 1990 integrea too and this is how you remove it ... you have to remove your axle to get the alternator out ... i had the same problem before....... hopes this help you a bit ... i know it's a lot of work but that's the only way .........
How do you remove the half shaft on the rear axle of a 96 Jeep Grand Cherokee?
Raise car, chock front wheels and put jack stands underneath. Remove the tire. Drain differential. Remove the differential cover. If mating pin (Silver rod, the only brightly polished part in there) capscrew (Torx no. 10) is not visible, remove rear drive shaft and Turn axle until mating pin capscrew is visible. Remove capscrew and mating pin, do not let the cluster gears turn or they will come apart. Not impossible to put together but very aggrevating. Push the axle in from the side of the vehicle. Remove the yellow "C clip". Pull the axle from the side of the vehicle. Reverse order to reinstall.
Will 2008 Ford Crown Victoria radio wire harness fit a 2010 Ford Crown Victoria radio?
NO, not in my experience. The 2010 Crown Vic factory harness is wider that the harness that would connect to the OEM wiring in the 2008 Crown Vic. I am currently awaiting a replcement that according to a Crutchfield rep. should work.. After I described the configuration of the pins in the factory harness, he stated that it sounds like it is just the regular adapter that fits some of the 2010 and up Ford products, but I didn't show up on the Crutchfield website as being a mate to the 2010 Crown vic since they only listed harnesses for up to a 2008 Model Crown Vic.
