answersLogoWhite

0


Best Answer

here are a few tricks.some rotors have a threaded holes for bolts to be installed into.turn in the bolts a bit at a time to free from the flange.or remove the caliper and use a chunk of wood to protect the rotor and smack it with a large hammer.rotate the rotor a 1/4 turn and hit again repeat process till free.hit from backside of rotor.

User Avatar

Wiki User

โˆ™ 2009-06-21 21:43:15
This answer is:
๐Ÿฆƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: How do you remove stuck disc brake rotors?
Write your answer...
Submit
Related questions

How do you replace your disc brake rotors on a 1996 Ford Fairlane?

Remove wheels. Remove 2 bolts securing brake caliper. Slide caliper off and support. Rotors should slide off.


How do you replace the brake pads for the emergency brakes on a 2004 dodge ram 1500?

If the truck has disc brakes on the rear then the park brake shoes are located inside the rear rotors. You have to remove the brake calipers, pads and rotors to access them


Where is the rotor located on a Chevy S-10?

There should be two rotors if your truck is 2wd. They are located where the brake pads clamp to. Rotors are also called brake disc. It's the round disc between the brake pads.


How do you put on new rotors and disc brakes?

Remove the tire, remove the brake calipers( The part that holds the brack pads in place, Once that is removed, You can remove the brake rotors and put new ones on. Depending on the style of rotors, You may have to remove and repack the wheel bearings to put new rotors on. Most current cars and rotors are seprate from the lug nut assembaly. So when that you are done the rotor is held on by the caliper assembaly and your wheels lug nuts and a couple of guild pins. .


How many rotors on front brakes?

( 2 rotors on the front ) one for each DISC brake


How do you change rotors of a 1995 Elantra?

Remove the brake caliper but dont disconnect the brake line also remove the caliper mounting bracketRemove the steering knuckle and take it to properly equipped shop and have the hub flange pressed out of the knuckle then the disc can then be unbolted from the hubOn rear disc brakes remove the retaining screw and remove the disc from the hub


How do you remove the brake rotors on a 1998 Ford F-150 4.6 4X4?

# Raise and safely support the vehicle securely on jackstands. # Remove the brake caliper assembly. # Remove the front disc brake caliper anchor plate. # Remove the hub grease cap. # Remove the cotter pin. # Remove the spindle nut. # Remove the front wheel outer bearing retainer washer. # Remove the outer front wheel bearing. # Remove the hub grease cap gasket. # Remove the front disc brake hub and rotor. # Remove the wheel hub grease seal. # Remove the inner front wheel bearing.


How do you completely disengage the emergency brake to remove the rear brake disc rotors on a 95 Talon?

You do not need to disengage the emergency brake to remove the rotors. Go to the local Auto store and get yourself an emergency brake spring remover. You will use this to take the spring off and use it to put it back on afterwards. I've used pliers before but its a real pain. The tool will make it 10 times easier. I think this is what you meant.


How do you remove brake rotors from part with lugs on a 1996 Toyota T100. I already know how to remove the rotor from the front wheel axle.?

On 2.WD pick-up models, the disc is bolted to the backside of the hub.


Disc brake assembly install for 1967 Chevelle?

It's pretty straightforward. You will need to change the spindles, brake lines, brake hoses and master cylinder. You will also need to install a proportioning valve from a disc brake car, preferably another Chevelle. Stick with stock calipers and rotors if you intend on using stock wheels because many of the aftermarket disc brake setups have larger rotors and calipers that will NOT work with stock wheels.


How do you Replace front brake rotors on a 1997chrysler cirrus?

all you have to do is un bolt the whole assembly with two bolts on the inside of the brakes and the whole unit should lift off the the rotor should pull right off. if they are stuck use a rubber malet to slightly remove it without scratching the disc.


Do new brake drums need to be cut?

Brake drums can not be cut. The shoes inside can be replaced.Only disc brakes(rotors) can cut.


How often do you replace brake rotors?

when there is a visable rigde / lip on the edge of the disc (rotor) when there is a visable rigde / lip on the edge of the disc (rotor)


How do you remove front disc brakes on 1988 Honda civic?

You have to remeove the disc brake calipers first by removing the 17 mm bolts connecting them to the strut , the there are 2 screws on the front when they are off the rotors are ready to be removed, reassemble in reverse order


What would cause one front disc brake to heat up and smoke?

A frozen brake caliper or if you just instaled new brakes and rotors you might have oil on the rotors as they need to be clean before installing.


How do you prevent your disc rotors getting hot?

There no way to prevent them getting hot unless you don't brake


What brake pads for chrome disc rotors?

Are you sure the rotors are chrome. If they are chrome plated, the plating WILL wear off. They may be made of a Chrome Moly steel.....which is typical for rotors because of it's strength.


How do you remove and replace the front right rotor on a 2000 Lincoln Navigator?

AnswerRemovalRemove the front disc brake caliper anchor plate. On 4x4 vehicles, remove the brake disc. On 4x2 vehicles, remove the brake disc and hub as follows: Remove the hub grease cap. Remove the cotter pin. Remove the nut retainer. Remove the spindle nut. Remove the front wheel outer bearing retainer washer. Remove the outer front wheel bearing. Remove the brake disc and hub.Remove the wheel hub grease seal. Remove the inner front wheel bearing.InstallationOn 4x4 vehicles, position the brake disc. Clean the brake disc. Position the brake disc. On 4x2 vehicles thoroughly clean and inspect the front wheel bearings and the brake disc and hub.On 4x2 vehicles, lubricate the front wheel bearings. On 4x2 vehicles, install a new wheel hub grease seal. Install the inner front wheel bearing. Install a new wheel hub grease seal.On 4x2 vehicles, install the brake disc and hub. Position the brake disc and hub. Install the outer front wheel bearing. Install the front wheel outer bearing retainer washer. Install the spindle nut.NOTE: On 4x2 vehicles, rotate the brake disc and hub while adjusting front wheel bearing end play.Tighten the spindle nut. Loosen the spindle nut two turns. Tighten the spindle nut while rotating the brake disc counterclockwise. Loosen the spindle nut. Tighten the spindle nut.On 4x2 vehicles, install the following components: nut retainer cotter pin hub grease cap_____________________________________Removing Front & Rear RotorsI remove my Front & Rear Rotors out of my 1998 Ford Expedition XLT.I rented a 3 Jaw Puller from Auto Zone and a bottle of PB Blaster and a sledge hammer it only took about one hour or less to take both off...The way I removed the Front & Rear Rotors was ...1. I put lots of PB Blaster in the back and the front of the rotors to be removed.2. I put plenty of tension with the 3 Jaw Puller...3. I hit the back of the rotor with the sledge hammer while rotating rotor...And it came right off...Hope this helps...


How do you remove the front disc brake rotors from a '96 Ford Aspire?

Remove the hubcaps and wheels. Remove the two large bolts that hold the brake caliper to the steering knuckle. pull the caliper out of the way. There are two large Philips head screws that hold the rotor to the hub. Remove them and slide the rotor off the hub. Just did this to my '96. Hope it helps


How do you remove the rear discs 2000 crown Victoria?

You have to remove the brake caliper first. Then you might have to slack the parking brake. The parking brake on read disc in inside the back of the rotor. If you cannot slack the parking brake, the you will have to hit the rotor ( with a small 5 lb hammer ) to loosen it. Might take a little time if it is stuck on.


How do you remove the rear rotor on a 2002 F150?

Removal # NOTE: When removing the rear brake disc (2C026) in this procedure it is not necessary to disconnect the hydraulic lines. Remove the rear disc brake caliper (2552). For additional information, refer to Caliper in this section. # NOTE: If the rear brake disc binds on the rear parking brake shoe and linings, remove the adjustment hole access plug and contract the parking brake shoe and lining. Remove the rear brake disc.


What kind of brakes does Mitsubishi Galant have Does it have rear brakes and rotors?

I believe the awnser varies on what model you have... I have a 1999 galant GTZ mine has disc ( rotors ) front and back, The rear has the disc drum combo for the parking brake... Hope this helps


How many rotors are on car?

It would depend if your car has 4 wheel disc brake or only the front (2) has disc brakes. You would have one rotor for each wheel with disc brakes.


What is the average life span of rotors and brake pads on a 95 Ford Probe?

The disc brake pads usually last 40,000 to 50,000 miles under normal conditions. The rotors should last for 2 brake jobs unless they have been run metal to metal.


What are disc brake rotors?

They are large steel discs that are bolted directly to the outer axles and absorb the pressure of brake pads to slow the vehicle. Theyare generally easy to remove and cheap to change. If good, they will look shiny and smooth. If scored or blue, they need to be changed.