0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you remove the third row seat in an expedition?
On the 1997-2000 Ford Expedition models the 3rd row seat are remove by. Folding seat in half then pull handle in the rear of the center of the seat bottom portion of the seat up. Pull handle and push top of seat forward. Be very careful the 3rd row seat is very heavy. Best bet is to get someone to help to fit it out.
What years are compatible with a 2000 ford expedition 3rd row seat?
1997 thru 2000 are all compatible
How do you remove 3rd seat in 2002 Mercury Villager Sport Van?
You can not remove the third seat. You can remove the second seat and slide the third seat into it's position to get more room in the back. You can also put the third seat in the upright position and move it all the way to the front for more cargo room.
Can you remove the 3rd row seat in a 2003 Acura MDX?
not unless you unbolt it from the vehicle
Does a 2000 Ford Explorer have third row seat?
No , it wasn't until the 2002 redesign of the 4 door Ford Explorer that a third row seat was available
Remove the 3rd row seating in a 2000 Lincoln Navigator?
There is a switch on the side of the seat that u must flip down to fold the seat down. then u have to raise it up and slide it out. the bottom has wheels on it. You dont have to fold the seat down, but i didnt even know that you could fold the seat down until this year....I thought that u couldnt. the latch to let the seat down is under the lilltle cover on the side of the seat.
How do you remove a front seat from a karmann ghia?
1st step remove the resorts (springs) 2nd step push on the safety located on the front bottom 3rd step pull lever 4th step push seat forward
Does a 1996 Chevy Tahoe come with a third row seat option?
nope, sorry. They didnt start adding 3rd row till the 2000 model came out.
How do you replace third brake light on a 2010 Hyundai Sonata?
I just changed the 3rd brake light in my 2010 Sonata - what an ordeal! But I saved the $50 the dealer wanted to charge me! 1. In the trunk, unplug the wire that feeds the 3rdtail light. 2. Remove the rear seat. Remove two 12mm (I think) bolts about 1/3rd and 2/3rd across seat in crack between seat bottom and seat back (where your rear end would be). Pull forward on the two plastic clips in the front of the seat bottom (where you would put your hands to lift up the seat or where the backs of your calves would be). Pull seat out. 3. Remove left and right seat back end cushions. Remove 12mm bolt at the bottom and wack upward (I did this with a rubber mallet) to unhook it from the top hook. Note: these will be a bear to put back in. 4. Fold down both rear seat backs. 5. Remove the thin, black plastic "frame" around the opening. 6. Remove the small "SRS Airbag" medallion in both "C" pillars to expose the philips screw. Remove the screw and the plastic cover from the "C" pillar. It is held in by the one screw and many clips. You might have to pop some of it out with a screwdriver. Be careful, the side airbags are in there. 7. Now you can remove the rear deck. It is just held in by one clip (looks like a small yellow drywall anchor) which is visible and accessible in the trunk. 8. Now all you have to do is remove the housing, I think by removing just 2 small screws, and change the light bulb (bulb #921). Hope this helps. Good luck.
Where is the tire jack for the 2006 Nissan quest located?
I have a 2000 quest, and the jack is under the 3rd row seat in a pouch anging, don't know if is the same in a 2006. Hope this helps.
How do you put a third row seat on 1999 ford explorer?
It's not designed for a 3rd row seat , Ford didn't offer a 3rd row seat in the 4 door Explorer until the 2002 model
How do you remove the rear seat in a 1994 mercury villager van?
I removed the bench seat by removing the seat tracks...4 bolts on each side beneath the carpet. I just use the the 2 rear bucket seats now and take them out when I need the room for cargo. Saves about 150 lbs which gives better performance as well. You could also take the tracks to a machine or welding shop and have them cut off the rear of the tracks where the stops prevents you from sliding the bench seat out. I thought of that but really haven't found the need for the 3rd seat, so I'm sticking to the former approach. ----- 1 - remove the middle row for easy access 2 - remove the 6 bolts attaching the seat to the sliding brackets 3 - remove bench seat from van. It is very heavy. To remove sliding brackets: 1 - remove trim piece by sliding door or cut away carpet 2 - remove captains chairs in the front seat 3 - unscrew the wiring harness and heater vent 4 - lift carpet & wiring harness while sliding the seat bracket off the track. 5 - repeat on other side 6 - reassemble everything.
