0
How do you remove the axles from a 1989 Mazda 323 1.6l manual transaxle?
Wiki User
∙ 14y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you remove a trans axle in 97 Mazda 626?
Its a time consuming job but not to bad, remove both trans axles (CV shaft) that go to tran.. Hanes manual says put sockets in each side. remove the bottom supports (cross members) remove starter , clutch slave, everything attacthed to transaxle, support the tranny and then remove the top engine mount...
CV axles remove 2000 sonata?
how does the cv axle on the driver side removed it wont come out of the transaxle 4cly auto 2002 sonata
What are the steps in pulling a 3-speed auto in a 1998 2.2 Pontiac Sunfire?
Disconnect the negative battery cable. Properly drain the transaxle. Remove the air intake duct. Disconnect the TV cable. Remove the shift cable and bracket. Tag and detach all necessary vacuum lines and electrical connections. Remove the power steering pump and set aside. Remove the transaxle filler tube. Install engine support fixture J 28467-A or equivalent. Remove the top engine-to-transaxle bolts. Raise and safely support the vehicle. Remove both front tire and wheel assemblies. Remove the left splash shield. Remove both front ABS wheel speed sensors and the harness from the left suspension support. remove both lower ball joints. Disconnect the stabilizer shaft links. Remove the front air deflector. Remove the left suspension support and both drive axles. Disconnect the engine-to-transaxle brace, then remove the transaxle converter cover. Remove the starter Unfasten the flywheel-to-torque converter bolts. Disconnect the transaxle cooler pipes. Detach the ground wires from the engine-to-transaxle bolt. Remove the cooler pipe brace and the exhaust brace. Remove the bolts from the engine and transaxle mount. Support the transaxle with a suitable jack. Unfasten the transaxle mount-to-body bolts. Remove the heater core hose pipe brace-to-transaxle nut and bolt. Unfasten the remaining engine-to-transaxle bolts, then remove the transaxle assembly from the vehicle.
What is the power train of a front wheel drive car?
The engine, transaxle and axles (half-shafts).
How do you replace the automatic transmission on a 1997 Hyundai Elantra?
1. Disconnect negative battery cable. Remove battery and battery tray 2. Remove the air intake duct and the air cleaner housing 3. Disconnect the transaxle ground cable and the transaxle range sensor 4. Disconnect the transaxle harness connector from the side of transaxle 5. Drain the transaxle fluid then disconnect the transaxle cooling lines 6. Remove the upper transaxle-to-engine mounting bolt 7. Raise the car and support it on jack stands. Secure the engine with a engine support brace or with an engine lift and chain. 8. Remove the transaxle mount bracket 9. Remove the front wheels 10. Remove the bolts from the center member and the transaxle roll stopper 11. Disconnect the lower control arms from the steering knuckle and remove drive axles 12. Remove the transaxle stay followed by the bell housing access cover 13. Remove the torque converter bolts. A screwdriver wedged in the ring gear teeth will keep the torque converter from rotating. Rotate the engine for access to all bolts 14. Support transaxle with transmission Jack to lower transaxle from car 15. Make final check everything is disconnected 16. Remove the mounting and retaining bolts and lower transaxle from the car
How do you remove a 1997 Ford Escort transmission?
That depends on whether you have a manual 5 speed or an automatic. On both you have to support the engine from above since 2 of the 3 mounts are on the transmission. Disconnect all the electrical connections. Remove the bolts and nuts that hold the left hand engine mount. Remove the upper front and upper rear bolts that hold the trans. to the engine. Remove the starter motor. Remove the drive axles. Drain the transaxle fluid Remove the crossmember. Unbolt the gear shift rod from the input shaft of the transmission. Remove the nut that holds the gear shift bar to the transaxle. Then slide the bar off the stud. Remove the clutch slave cylinder. Remove the 2 lower bolts that hold the transaxle to the engine. Put a transmission jack under the transmission Remove the catalytic converter. With the transmission supported well, remove the last 3 bolts that hold the engine to the transmission. Carefully lower the transaxle and slide it from the engine.
What axles will interchange with a 1994 Ford Probe 5 speed?
the Mazda 626 and the Mazda rx7 are interchangeble.
How do you install transaxel in Toyota Tercel 1995?
You generally start by dropping both front axles at the transaxle then disconnecting all electrical, hydraulic, control, refrigerant, and fuel lines then disconnecting the motor mounts and hoisting the engine/transaxle assembly out as a unit. From there, you unbolt the bellhousing of the transaxle and split it off. Installation is the reverse. Find a good shop manual and a buddy who has done it before. The job will require at least a case of beer.
How do you take apart the axles on a 90 civic DX?
the only parts that you can replace on the axle shaft are the cv joints that go into transaxle Cheaper to buy new axles 75 to 100 each side
How do you change a clutch on a 2003 volkswagen jetta 1.8t?
The short story: remove shift linkage. Remove axles. Remove transmission (engine stays in car). replace clutch. You must have a manual to do this job, or it will not work. Even mechanics who do this job will work from a book.
What are the steps to remove and then replace the transmission on a 1996 Pontiac Sunfire?
1. Disconnect the negative battery cable. 2. Properly drain the transaxle. 3. Remove the air intake duct. 4. Disconnect the TV cable. Remove the shift cable and bracket. 5. Tag and detach all necessary vacuum lines and electrical connections. 6. Remove the power steering pump and set aside. 7. Remove the transaxle filler tube. 8. Install engine support fixture J 28467-A or equivalent. 9. Remove the top engine-to-transaxle bolts. 10. Raise and safely support the vehicle. 11. Remove both front tire and wheel assemblies. Remove the left splash shield. 12. Remove both front ABS wheel speed sensors and the harness from the left suspension support. 13. remove both lower ball joints. 14. Disconnect the stabilizer shaft links. 15. Remove the front air deflector. 16. Remove the left suspension support and both drive axles. 17. Disconnect the engine-to-transaxle brace, then remove the transaxle converter cover. 18. Remove the starter 19. Unfasten the flywheel-to-torque converter bolts. 20. Disconnect the transaxle cooler pipes. 21. Detach the ground wires from the engine-to-transaxle bolt. 22. Remove the cooler pipe brace and the exhaust brace. 23. Remove the bolts from the engine and transaxle mount. 24. Support the transaxle with a suitable jack. 25. Unfasten the transaxle mount-to-body bolts. 26. Remove the heater core hose pipe brace-to-transaxle nut and bolt. 27. Unfasten the remaining engine-to-transaxle bolts, then remove the transaxle assembly from the vehicle. 28. Place a thin film of GM part no. 1051344 or equivalent grease on the torque converter pilot knob. 29. Move the transaxle assembly into position with the jack while installing the right drive axle. Make sure to properly seat the torque converter in the oil pump. 30. Install the lower transaxle retaining bolts in their proper positions, as shown in the accompanying figure. 31. Install the transaxle mount-to-body bolts as shown in the accompanying figure. 32. Install the engine and transaxle mount bolts. 33. Fasten the exhaust brace and the cooler pipe brace. 34. Connect the ground wires at the engine-to-transaxle bolt. 35. Attach the transaxle cooler pipes. 36. Apply adhesive/sealing compound GM part no. 12345493 or equivalent on the flywheel-to-torque converter bolts, then install the bolts. Install the converter cover/shield. 37. Install the starter. 38. Fasten the engine-to-transaxle brace. 39. Install the drive axles and the left suspension support. 40. Fasten the front air deflector. 41. Connect the stabilizer shaft links and the lower ball joints. 42. Install both ABS wheel speed sensors. 43. Fasten the left splash shield, then install the heater core pipe brace nut and bolt. 44. Install the front wheel and tire assemblies, then carefully lower the vehicle. 45. Install the top engine-to-transaxle bolts. 46. Remove the engine support fixture. 47. Install the filler tube. 48. Install the power steering pump assembly, then adjust the belt. 49. Attach the electrical connections and vacuum lines, as tagged during removal. 50. Install the shift cable and bracket. Connect the TV cable. 51. Fasten the air intake duct. 52. Connect the negative battery cable, then fill the transaxle to the proper level.
When removing the transmission from a fwd car do you have to remove the axles?
yes
