there are two bolts in the back of the seat. remove them and then slide the seat back about an inch and remove
how to remove 2004 scion back seat
To remove the back seat of a Skylark, reach into the area between the back and the seat and pull up on the seat. The back part of the seat is bolted in and will require a socket wrench to remove.
well the first thing is to remove the lower seat. It has two clips near the front of it . Remove the lower seat now. Next remove the side panel right above the back seat. Now you have to remove the bolts for the seat belts, it holds the back part of the seat in. move the back part of the seat up towards the back window. You should hear the seat come loose. Now when you put the seat back in don't forget to pull the seat belts back though.
To remove the back seat of a 1998 Toyota Corolla, you will need to remove the carpet to expose the bolts for the seat. Then, loosen the bolts by removing the nuts. You can then remove the seat.
remove back seat jeep
Remove the bolts fastening the rear seat cushion (Figure 7.52).Remove the rear seat cushion assembly.Remove the screws and remove the side rear seat back (Figure 7.53).Remove the lower bolts fastening the rear seat back.Tightening torque - 17-26 NmFlip forward the rear seat back, remove the bolts and remove the back seat.Tightening torque - 17-26 Nm
First you remove the lower back seat, and the bolts that secure the upper will be exposed. Remove them and lift out upper back seat.
the back of the seat is the front of the trunk. To remove the rear seat back you first have to remove the two bolts just under bottom seat assembly. Bolts are located at the botton of lower seat, about between your ankles if you were sitting in the seat, one on each side. Then remove bottom seat assembly. Then remove seatbelt bolts that hold seat back assembly, lift straight up on seat back and remove.
To remove the back seat on a 1989 Ford Thunderbird, the first step is to remove the back of the seat. The back is held in by bolts on each side. After the back is removed, the seat area should come out after removing the floor bolts.
remove the 2 bolts at the bottom of the seat and then remove the bottom of the seat. Then remove the two star bolts at the bottom holding the seatbelts in place, then lift the seat on both sides to remove the back of the seat from its clips. Then your all done
remove bolt on the back of passenger seat, pull that back and out. Then driver seat just pulls back and out as well.
At the back of the seat is a chrome T40 Torx head screw into the fender. Remove it, lift the back of the seat and slide it backwards.
Push back on the bottom of the bench seat (takes a lot of pressure) to release holding clips Lift bench out Back of seat is secured by clips or bolts that are now accessible - remove these and lift upward on back of seat to release upper clips Remove seat back
Just push back on the seat and lift.
Remove lower seat bottom. Remove two bolts from bottom of seat back. Lift seat back off of its hooks. Remove from car. Use Philips screwdriver to remove 4 screws holding speaker grille to seat back frame.
Check out the related link for instructions on how to remove the back seat from a Subaru Impreza.
You remove the center seat and slide the back one up into it's place.
unscrew the bolts and take the seat out
To remove the back seat from most GM vehicles, Lift the front of the seat section then pull the seat forward. After the seat bottom is removed, there should be a couple bolts holding the bottom of the seat back into place. After removing those bolts you should be able to lift the seat straight up and remove it.
Remove the Allen head bolt that fastens the passenger seat . Then lift this seat upward and pull it back to remove it. Next, find the two bolts that fasten the rider's seat at the rear. Remove them and lift the seat up and pull it back a bit.
Move the seat all the way forward then remove the nuts or bolts from rear. Move the seat all the way back then remove the front nuts or bolts. Tip the seat back and disconnect the electrical plug(s). Remove the seat from vehicle.
Remove the bolts holding the seat on each side and then slide the seat back.
There should be a lever on the bottom of the back seat. It is located on the lower corner of the back seat, and it allows the back seat to come out in one piece.